 English |
|
|
|
|
|
|
|
| XC5VLX110T-2FFG1738I Datasheet, PDF (2/91 Pages) Xilinx, Inc – Virtex-5 FPGA Packaging and Pinout Specification | |||
| |||
| ◁ |
Virtex-5 FPGA Data Sheet: DC and Switching Characteristics
Table 2: Recommended Operating Conditions
Symbol
Description
Temperature Range
Min
Max Units
VCCINT
Internal supply voltage relative to GND, TJ = 0°C to +85°C
Internal supply voltage relative to GND, TJ = â40°C to +100°C
VCCAUX(1)
Auxiliary supply voltage relative to GND, TJ = 0°C to +85°C
Auxiliary supply voltage relative to GND, TJ = â40°C to +100°C
VCCO(2,4,5)
Supply voltage relative to GND, TJ = 0°C to +85°C
Supply voltage relative to GND, TJ = â40°C to +100°C
3.3V supply voltage relative to GND, TJ = 0°C to +85°C
3.3V supply voltage relative to GND, TJ = â40°C to +100°C
VIN
2.5V and below supply voltage relative to GND,
TJ = 0°C to +85°C
2.5V and below supply voltage relative to GND,
TJ = â40°C to +100°C
IIN(6)
Maximum current through any pin in a powered or unpowered
bank when forward biasing the clamp diode
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
Commercial
Industrial
0.95
1.05
V
0.95
1.05
V
2.375
2.625
V
2.375
2.625
V
1.14
3.45
V
1.14
3.45
V
GND â 0.20 3.45
V
GND â 0.20 3.45
V
GND â 0.20 VCCO + 0.2 V
GND â 0.20 VCCO + 0.2 V
10
mA
10
mA
VBATT(3)
Battery voltage relative to GND, TJ = 0°C to +85°C
Battery voltage relative to GND, TJ = â40°C to +100°C
Commercial
Industrial
1.0
3.6
V
1.0
3.6
V
Notes:
1. Recommended maximum voltage drop for VCCAUX is 10 mV/ms.
2. Configuration data is retained even if VCCO drops to 0V.
3. VBATT is required only when using bitstream encryption. If battery is not used, connect VBATT to either ground or VCCAUX.
4. Includes VCCO of 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V.
5. The configuration supply voltage VCC_CONFIG is also known as VCCO_0.
6. A total of 100 mA per bank should not be exceeded.
Table 3: DC Characteristics Over Recommended Operating Conditions
Symbol
Description
Data Rate Min Typ Max Units
VDRINT
VDRI
IREF
IL
CIN
IRPU(1)
IRPD(1)
IBATT(2)
n
Data retention VCCINT voltage (below which configuration data might be lost)
Data retention VCCAUX voltage (below which configuration data might be lost)
VREF leakage current per pin
Input or output leakage current per pin (sample-tested)
Input capacitance (sample-tested)
Pad pull-up (when selected) @ VIN = 0V, VCCO = 3.3V
Pad pull-up (when selected) @ VIN = 0V, VCCO = 2.5V
Pad pull-up (when selected) @ VIN = 0V, VCCO = 1.8V
Pad pull-up (when selected) @ VIN = 0V, VCCO = 1.5V
Pad pull-up (when selected) @ VIN = 0V, VCCO = 1.2V
Pad pull-down (when selected) @ VIN = 2.5V
Battery supply current
Temperature diode ideality factor
0.75
V
2.0
V
10 µA
10 µA
8
pF
20
150 µA
10
90 µA
5
45 µA
3
30 µA
2
15 µA
5
110 µA
150 nA
1.0002
n
r
Series resistance
5.0
Ω
Notes:
1. Typical values are specified at nominal voltage, 25°C.
2. Maximum value specified for worst case process at 25°C.
DS202 (v5.3) May 5, 2010
www.xilinx.com
Product Specification
2
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese