XC5VLX110T-2FFG1738I Datasheet, PDF (13/91 Pages) Xilinx, Inc – Virtex-5 FPGA Packaging and Pinout Specification

Virtex-5 FPGA Data Sheet: DC and Switching Characteristics
GTP_DUAL Tile Specifications
GTP_DUAL Tile DC Characteristics
Table 24: Absolute Maximum Ratings for GTP_DUAL Tiles
Symbol
Description
MGTAVCCPLL Analog supply voltage for the GTP_DUAL shared PLL relative to GND
MGTAVTTTX Analog supply voltage for the GTP_DUAL transmitters relative to GND
MGTAVTTRX Analog supply voltage for the GTP_DUAL receivers relative to GND
MGTAVCC Analog supply voltage for the GTP_DUAL common circuits relative to GND
MGTAVTTRXC Analog supply voltage for the resistor calibration circuit of the GTP_DUAL
column
–0.5 to 1.32
–0.5 to 1.32
–0.5 to 1.32
–0.5 to 1.1
–0.5 to 1.32
Units
V
V
V
V
V
Notes:
1. Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied.
Exposure to Absolute Maximum Ratings conditions for extended periods of time might affect device reliability.
Table 25: Recommended Operating Conditions for GTP_DUAL Tiles⁽¹⁾⁽²⁾
Symbol
Description
Min
MGTAVCCPLL⁽¹⁾ Analog supply voltage for the GTP_DUAL shared PLL relative to GND
1.14
MGTAVTTTX⁽¹⁾ Analog supply voltage for the GTP_DUAL transmitters relative to GND
1.14
MGTAVTTRX⁽¹⁾ Analog supply voltage for the GTP_DUAL receivers relative to GND
1.14
MGTAVCC⁽¹⁾ Analog supply voltage for the GTP_DUAL common circuits relative to GND
0.95
MGTAVTTRXC⁽¹⁾ Analog supply voltage for the resistor calibration circuit of the GTP_DUAL
1.14
column
Max
1.26
1.26
1.26
1.05
1.26
Notes:
1. Each voltage listed requires the filter circuit described in UG196: Virtex-5 FPGA RocketIO GTP Transceiver User Guide.
2. Voltages are specified for the temperature range of T_J = –40°C to +100°C.
Table 26: DC Characteristics Over Recommended Operating Conditions for GTP_DUAL Tiles⁽¹⁾
Symbol
I_MGTAVTTTX
I_MGTAVCCPLL
I_MGTAVTTRXC
I_MGTAVTTRX
I_MGTAVCC
MGTR_REF
Description
GTP_DUAL tile transmitter termination supply current⁽²⁾
GTP_DUAL tile shared PLL supply current
GTP_DUAL tile resistor termination calibration supply current
GTP_DUAL tile receiver termination supply current⁽³⁾
GTP_DUAL tile internal analog supply current
Precision reference resistor for internal calibration termination
Min
Typ
Max
71
90
36
60
0.1
0.5
0.1
0.5
56
110
49.9 ± 1% tolerance
Notes:
1. Typical values are specified at nominal voltage, 25°C, with a 3.2 Gb/s line rate.
2. ICC numbers are given per GTP_DUAL tile with both GTP transceivers operating with default settings.
3. AC coupled TX/RX link.
Units
V
V
V
V
V
Units
mA
mA
mA
mA
mA
Ω
DS202 (v5.3) May 5, 2010
www.xilinx.com
Product Specification
13