PIC24FJ16MC101_12 Datasheet, PDF (1/350 Pages) Microchip Technology – 16-bit Microcontrollers (up to 32 KB Flash and 2 KB SRAM)

PIC24FJ16MC101/102 AND
PIC24FJ32MC101/102/104
16-bit Microcontrollers
(up to 32 KB Flash and 2 KB SRAM)
Operating Conditions
• 3.0V to 3.6V, -40ºC to +125ºC, DC to 16 MIPS
Core: 16-bit PIC24F CPU
• Code-efficient (C and Assembly) architecture
• Two 40-bit wide accumulators
• Single-cycle (MAC/MPY) with dual data fetch
• Single-cycle mixed-sign MUL plus hardware divide
• 32-bit multiply support
Clock Management
• ±0.25% internal oscillator
• Programmable PLLs and oscillator clock sources
• Fail-Safe Clock Monitor (FSCM)
• Independent Watchdog Timer (WDT)
• Fast wake-up and start-up
Power Management
• Low-power management modes (Sleep, Idle, Doze)
• Integrated Power-on Reset and Brown-out Reset
• 1 mA/MHz dynamic current (typical)
• 30 µA IPD current (typical)
PWM
• Up to three PWM pairs
• Two dead time generators
• 31.25 ns PWM resolution
• PWM support for:
- Inverters, PFC, UPS
- BLDC, PMSM, ACIM, SRM
• Class B-compliant Fault inputs
• Possibility of ADC synchronization with PWM signal
Advanced Analog Features
• ADC module:
- 10-bit, 1.1 Msps with four S&H
- Six analog inputs on 20-pin devices, eight analog
inputs on 28-pin devices, and up to 16 analog inputs
on 44-pin devices
• Flexible and independent ADC trigger sources
• Three Comparator modules
• Charge Time Measurement Unit (CTMU):
- Supports mTouch™ capacitive touch sensing
- Provides high-resolution time measurement (1 ns)
- On-chip temperature measurement
Timers/Output Compare/Input Capture
• Five general purpose timers:
- One 16-bit and two 32-bit timers/counters
• Two Output Compare modules
• Three Input Capture modules
• Peripheral Pin Select (PPS) to allow function remap
Communication Interfaces
• UART module (4 Mbps)
- With support for LIN 2.0 protocols and IrDA^®
• 4-wire SPI module (8 MHz maximum speed)
- Remappable pins in 32 KB Flash devices
• I²C™ module (400 kHz)
Input/Output
• Sink/Source 10 mA or 6 mA, on specific for standard
VOH/VOL, up to 16 mA or 12 mA for non-standard VOH1
• 5V-tolerant pins
• Up to 21 open drain, pull-ups, and pull-downs
• External interrupts on most I/O pins
Qualification and Class B Support
• AEC-Q100 REVG (Grade 1 -40ºC to +125ºC) planned
• Class B Safety Library, IEC 60730, UDE certified
Debugger Development Support
• In-circuit and in-application programming
• Up to three complex data breakpoints
• Trace and run-time watch
Packages
Type
Pin Count
PDIP SPDIP
20
28
SOIC
20
28
SSOP
20
28
TQFP
44
I/O Pins
15
21
15
21
15
21
35
Contact Lead/Pitch .100” .100” 1.27 1.27 0.65 0.65
0.8
Dimensions Please see Section 27.2 “Package Details” for this information.
QFN
28
44
21
35
0.65 0.65
VTLA
36
44
21
35
0.5
0.5
© 2011-2012 Microchip Technology Inc.
Preliminary
DS39997C-page 1