GRJ43DR72J104KWJ1L Datasheet, PDF (77/221 Pages) Murata Manufacturing Co., Ltd. – Chip Monolithic Ceramic Capacitors

C02E.pdf !Note • Th!is PNDoFteca•1ta.PlTolehgaissiseSdrpoeewacdniflirocaattdinioegndsafnraodnmd!tThCeeAswUt MeTbIeOsthiNteod(ofsof riMssutdoroarwatagnelMo,aodnpeuedfraafctritonumgri,ntrghaetcinowg.e,,bltsdsoi.tldeTehorefinrMegf,uomrraeot,auinMt’tsiannsgpuaefanccdiftiuchraaintnigodnlcisnog.a,)lrteidn.stTuhhbisejercceatftotaorleoc,ghitat'osngspepreeovcreifonicutarstmipornooskdiunacgretsasniundb/iotjermcbtautyornbcienhgad,nisegcteco.notrinouuerdprwoidthuocutst aindvitamncaey nboetidcies.coPnletiansueedchweicthkowuitthadovuarnce notice.
sales repres_•0e.TnPt_ha_ilsteivacesasetaoclorhgperchokad_swuciotthne_lyonutg_yri_pnsieacelaer_lssrpbeeepcforiefr_icesaeo_tnir_otdanetsirvi_bneegsc.oarupsreodthuecrteeinsgninoeseprascbeeffoorredeotradileerdinsgp. _{ecifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
10.12.20 ^{• This PDF ca}2^ta. ^lT^oh^gis^haS^spe^ocⁿi^lf^yic^ta^yt^pio^icn^as^l a^spn^ed^cT^ife^ics^at^tM^ione^sth^bo^ed^cs^ah^ua^ss^eo^thn^ely^retyⁱp^sicⁿa^ol ^ss^pp^ae^cc^eific^foa^rti^do^en^ts^aib^lee^dca^su^ps^ee^cit^fh^ice^ar^te^ioiⁿs^sn^.o^Thsp^ea^rec^fe^orf^eo^,r ^pd^le^et^aa^sil^eed^aps^pp^re^oc^vi^efic^oa^uti^ro^pn^rs^o.^dT^uh^ce^tr^se^pfo^er^ce^if,^icp^ale^tia^osⁿe^s a^op^r p^trr^aoⁿv^se^ao^cu^t r^thp^ero^ad^pu^pc^rt^os^vp^ae^l c^si^hfi^ec^ea^ttio^fon^rs^po^ror ^dtr^ua^cn^ts^sa^pc^et^cth^ifie^caa^tp^iopⁿr^sov^ba^el^fs^oh^reee^ot^rdfo^er^ripⁿr^go^.duct
0. specifications before ordering.
GNM Series Specifications and TGesNtMMSetehroiedssS(2p)ecifications and Test Methods (2)
Continued from the preceding page.
When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).
No.
Item
Specifications
Test Method
Appearance No marking defects
Capacitance
Change
Within ±10%
#GNMpp4
#GNMpp2
Solder the capacitor to the test jig (glass epoxy board) shown in
Fig. 2 using a eutectic solder. Then apply a force in the
direction shown in Fig. 3. The soldering should be done by the
reflow method and should be conducted with care so that the
soldering is uniform and free of defects such as heat shock.
12 Deflection
5.0
a
b
dc
Type
GNM0M2
GNM1M2
GNM212
GNM214
GNM314
100
100
5.0
a
b
1.0
c 1.0
d
Thickness: 0.8mm
a
b
c
d
2.0±0.05 0.2±0.05 0.2±0.05 0.25±0.05
2.0±0.05 0.5±0.05 0.32±0.05 0.32±0.05
2.0±0.05 0.6±0.05 0.5±0.05 0.5±0.05
2.0±0.05 0.7±0.05 0.3±0.05 0.2±0.05
2.5±0.05 0.8±0.05 0.4±0.05 0.4±0.05
(in mm)
Fig. 2
R230
20 ₅₀ Pressurizing
speed: 1.0mm/sec.
Pressurize
Capacitance meter
45
45
Fig. 3
Flexure : V1
13
Solderability of
Termination
75% of the terminations are to be soldered evenly
and continuously.
Appearance No marking defects
Capacitance R6*⁴: Within ±7.5%
Change *⁴ GNM0M2R60G105: Within +15/-7.5%
Resistance
14 to Soldering D.F.
Heat
0.1 max. *³
*³ However 0.125 max. for Table 3 items.
I.R.
50Ω · F min.
Dielectric
Strength
No failure
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120°C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2±0.5 seconds at 230±5°C or
Sn-3.0Ag-0.5Cu solder solution for 2±0.5 seconds at 245±5°C.
Preheat the capacitor at 120 to 150°C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270±5°C for 10±0.5 seconds.
Let sit at room temperature for 24±2 hours, then measure.
• Initial measurement
Perform a heat treatment at 150 +0/-10°C for one hour and
then let sit for 24±2 hours at room temperature. Perform
the initial measurement.
Appearance No marking defects
Fix the capacitor to the supporting jig in the same manner and
Capacitance
Change
R6*⁵: Within ±12.5%
*⁵ GNM0M2R60G105, GNM0M2R60J103/223/473/104,
GNM0M2R61A103/223/473/104,
GNM0M2R61C103/223/473/104, GNM1M2R61A105:
under the same conditions as (10).
Perform the five cycles according to the four heat treatments
listed in the following table.
Let sit for 24±2 hours at room temperature, then measure.
15
Temperature
Cycle
D.F.
0.1 max. *³
*³ However 0.125 max. for Table 3 items.
Within ±15%
Step
1
2
3
4
Temp.
(°C)
Min. Operating
Temp.
Room
Temp.
Min. Operating
Temp.
Room
Temp.
Time (min.) 30±3
2 to 3
30±3
2 to 3
I.R.
50Ω · F min.
Dielectric
Strength
No failure
• Initial measurement
Perform a heat treatment at 150 +0/-10 °C for one hour and
then let sit for 24±2 hours at room temperature.
Perform the initial measurement.
Appearance No marking defects
High
Capacitance
Change
R6: Within ±12.5%
16
Temperature
High
D.F.
0.2 max.
Humidity
(Steady)
I.R.
12.5Ω · F min.
Apply the rated voltage at 40±2°C and 90 to 95% humidity for
500±12 hours. The charge/discharge current is less than 50mA.
• Initial measurement
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24±2 hours at room temperature.
Perform the initial measurement.
• Measurement after test
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24±2 hours at room temperature, then
measure.
Appearance No marking defects
Capacitance
Change
R6: Within ±12.5%
D.F.
0.2 max.
17 Durability
I.R.
25Ω · F min.
Apply 150% (GNM1M2R61A225/1C105: 125% of the rated
voltage) of the rated voltage for 1000±12 hours at the
maximum operating temperature ±3°C. Let sit for 24±2 hours
at room temperature, then measure.
The charge/discharge current is less than 50mA.
• Initial measurement
Perform a heat treatment at 150 +0/-10°C for one hour
and then let sit for 24±2 hours at room temperature.
Perform the initial measurement.
• Measurement after test
Perform a heat treatment at 150 +0/-10°C for one hour and
then let sit for 24±2 hours at room temperature, then measure.
75