GRJ43DR72J104KWJ1L Datasheet, PDF (57/221 Pages) Murata Manufacturing Co., Ltd. – Chip Monolithic Ceramic Capacitors

C02E.pdf !Note • Th!is PNDoFteca•taPlolegasisedroewadnlroaatdinegdafnrodm!thCeAwUeTbIOsiNte(ofof rMsutoraratageM, aonpuefraactitnugri,nrgatcinog.,,ltsdo.ldTehreinregf,omreo,uint’tsinsgpaencdifichaatniodnlisnga)reinstuhbisjeccatttaolocghatongpereovreonut rsmprookdiuncgtsanind/iot rmbauyrnbiengd,isectco.ntinued without advance notice. Please check with our
sales repres_•e_Tnt_ha_istiv_ce_as_tao_lor _gpr_ho_ad_suc_ot_ne_lyn_tg_yi_pn_ie_ce_ar_ls_spb_ee_cfo_ifr_ice_ao_tir_od_ne_sri_bn_eg_c. _{ause there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
10.12.20 ^{• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
GRM GSRerMiesSeSrpieesciSfipceactiiofincsataionndsTaensdt MTestht oMdesth(1o)d(sN(o1t)e(N1)o-Tteyp1i)c-Tayl pInicsapleIcntsiopnection
Continued from the preceding page.
(Note 1) These Specifications and Test Methods indicate typical inspection.
Please refer to individual specifications (our product specifications or the approval sheet).
When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).
No.
Item
Specifications
Temperature
Compensating Type
High Dielectric Type
Test Method
The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance No defects or abnormalities
Capacitance Within ±5% or ±0.5pF
Change (whichever is larger)
B1, B3, R1, R6, R7, C8:
Within ±12.5%
F1, F5, E4: Within ±30%
Humidity
16 (Steady
State)
Q/D.F.
30pF and over: QU350
10pF and over
30pF and below:
QU275+2.5C
10pF and below:
QU200+10C
C: Nominal Capacitance (pF)
[R6, R7, C8]
W.V.: 100V
: 0.05 max. (CF0.068µF)
: 0.075 max. (CU0.068µF)
W.V.: 50/35/25/16/10V
: 0.05 max.
W.V.: 6.3/4V
: 0.075 max. (CF3.3µF)
: 0.125 max. (CU3.3µF)
[E4]
W.V.: 25Vmin: 0.05 max.
[F1, F5]
W.V.: 25V min.
: 0.075 max. (CF0.1µF)
: 0.125 max. (CU0.1µF)
W.V.: 16/10V: 0.15 max.
W.V.: 6.3V: 0.2 max.
Set the capacitor at 40±2°C and in 90 to 95% humidity for
500±12 hours.
Remove and set for 24±2 hours at room temperature, then
measure.
I.R.
More than 1,000MΩ or 50Ω · F (whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance No defects or abnormalities
Capacitance Within ±7.5% or ±0.75pF
Change (whichever is larger)
B1, B3, R1, R6, R7, C8:
Within ±12.5%
F1, F5, E4: Within ±30%
[W.V.: 10V max.]
F1, F5: Within +30/–40%
17
Humidity
Load
Q/D.F.
30pF and over: QU200
30pF and below:
QU100+10C/3
C: Nominal Capacitance (pF)
[B1, B3, R6, R7, C8]
W.V.: 100V
: 0.05 max. (CF0.068µF)
: 0.075 max. (CU0.068µF)
W.V.: 50/35/25/16/10V
: 0.05 max.
W.V.: 6.3/4V
: 0.075 max. (CF3.3µF)
: 0.125 max. (CU3.3µF)
[E4]
W.V.: 25Vmin: 0.05 max.
[F1, F5]
W.V.: 25V min.
: 0.075 max. (CF0.1µF)
: 0.125 max. (CU0.1µF)
W.V.: 16/10V: 0.15 max.
W.V.: 6.3V: 0.2 max.
Apply the rated voltage at 40±2°C and 90 to 95% humidity for
500±12 hours. Remove and set for 24±2 hours at room
temperature, then measure.
The charge/discharge current is less than 50mA.
•Initial measurement for F1, F5/10V max.
Apply the rated DC voltage for 1 hour at 40±2°C.
Remove and set for 24±2 hours at room temperature.
Perform initial measurement.
I.R.
More than 500MΩ or 25Ω · F (whichever is smaller)
Continued on the following page.
55