GRJ43DR72J104KWJ1L Datasheet, PDF (165/221 Pages) Murata Manufacturing Co., Ltd. – Chip Monolithic Ceramic Capacitors

C02E.pdf !Note • Th!is PNDoFteca•taPlolegasisedroewadnlroaatdinegdafnrodm!thCeAwUeTbIOsiNte(ofof rMsutoraratageM, aonpuefraactitnugri,nrgatcinog.,,ltsdo.ldTehreinregf,omreo,uint’tsinsgpaencdifichaatniodnlisnga)reinstuhbisjeccatttaolocghatongpereovreonut rsmprookdiuncgtsanind/iot rmbauyrnbiengd,isectco.ntinued without advance notice. Please check with our
sales repres_•e_Tnt_ha_istiv_ce_as_tao_lor _gpr_ho_ad_suc_ot_ne_lyn_tg_yi_pn_ie_ce_ar_ls_spb_ee_cfo_ifr_ice_ao_tir_od_ne_sri_bn_eg_c. _{ause there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
10.12.20 ^{• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
GMRedMiuSmerVieosltSagpecLifoicwaDtioisnssipaantdioTneFsatcMtoerthSopdescifications and Test Methods
No.
Item
Specifications
1
Operating
Temperature Range
2 Appearance
3 Dimensions
Y55 to W125D
No defects or abnormalities
Within the specified dimension
4 Dielectric Strength No defects or abnormalities
5
Insulation Resistance
(I.R.)
More than 10,000MΩ
6 Capacitance
Within the specified tolerance
7Q
1,000 min.
Capacitance
8 Temperature
Characteristics
Temp. Coefficient
C0G char. :
0T30ppm/D (Temp. Range : W25 to W125D)
0W30, Y72ppm/D (Temp. Range : Y55 to W25D)
U2J char. :
Y750T120ppm/D (Temp. Range : W25 to W125D)
Y750W120, Y347ppm/D (Temp. Range : Y55 to W25D)
9
Adhesive Strength
of Termination
No removal of the terminations or other defect should occur.
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
10
Vibration
Resistance
Q
1,000 min.
Test Method
Y
Visual inspection
Using calipers and micrometers
No failure should be observed when voltage in the Table is
applied between the terminations for 1 to 5 sec., provided the
charge/discharge current is less than 50mA.
Rated Voltage
DC250V
DC630V
DC1kV, DC2kV,
DC3.15kV
Test Voltage
200% of the rated voltage
150% of the rated voltage
130% of the rated voltage
The insulation resistance should be measured with DC500T50V
(DC250T25V in case of rated voltage: DC250V) and within 60T5
sec. of charging.
The capacitance/Q should be measured at the frequency and
voltage shown as follows.
Capacitance
CF1,000pF
CU1,000pF
Frequency
Voltage
1T0.2MHz AC0.5 to 5V(r.m.s.)
1T0.2kHz AC1T0.2V(r.m.s.)
The capacitance measurement should be made at each step
specified in the Table.
Step
1
2
3
4
5
Temperature (D)
25T2
Min. Operating Temp.T3
25T2
Max. Operating Temp.T2
25T2
Solder the capacitor to the testing jig (glass epoxy board) shown
in Fig. 1.
Then apply 10N force in the direction of the arrow.
The soldering should be done using the reflow method and
should be conducted with care so that the soldering is uniform
and free of defects such as heat shock.
10N, 10T1s
Glass Epoxy Board
Fig. 1
Solder the capacitor to the test jig (glass epoxy board).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should be
traversed in approximately 1 min. This motion should be applied
for a period of 2 hrs. in each of 3 mutually perpendicular
directions (total of 6 hrs.).
Glass Epoxy Board
Solder resist
Cu
Continued on the following page.
164