GRJ43DR72J104KWJ1L Datasheet, PDF (189/221 Pages) Murata Manufacturing Co., Ltd. – Chip Monolithic Ceramic Capacitors

C02E.pdf !Note • Th!is PNDoFteca•taPlolegasisedroewadnlroaatdinegdafnrodm!thCeAwUeTbIOsiNte(ofof rMsutoraratageM, aonpuefraactitnugri,nrgatcinog.,,ltsdo.ldTehreinregf,omreo,uint’tsinsgpaencdifichaatniodnlisnga)reinstuhbisjeccatttaolocghatongpereovreonut rsmprookdiuncgtsanind/iot rmbauyrnbiengd,isectco.ntinued without advance notice. Please check with our
sales repres_•e_Tnt_ha_istiv_ce_as_tao_lor _gpr_ho_ad_suc_ot_ne_lyn_tg_yi_pn_ie_ce_ar_ls_spb_ee_cfo_ifr_ice_ao_tir_od_ne_sri_bn_eg_c. _{ause there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
10.12.20 ^{• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
GACA25S0eVr(ire.ms .Ssp.)eTcyifpicea(tWiohnischanMdeeTteJsat pMaentehsoedLsaw) Specifications and Test Methods
No.
Item
Specifications
1
Operating
Temperature Range
2 Appearance
3 Dimensions
Y55 to W125D
No defects or abnormalities
Within the specified dimensions
4 Dielectric Strength No defects or abnormalities
5
Insulation Resistance
(I.R.)
More than 2,000MΩ
6 Capacitance
Within the specified tolerance
7
Dissipation
Factor (D.F.)
0.025 max.
Capacitance
8 Temperature
Characteristics
Cap. Change
Within T15%
(Temp. Range: Y55 to W125D)
Discharge
Test
9
(Application:
Nominal
Appearance
No defects or abnormalities
Capacitance
CF10,000pF)
10
Adhesive Strength
of Termination
No removal of the terminations or other defects should occur.
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
11
Vibration
Resistance
D.F.
0.025 max.
Test Method
Y
Visual inspection
Using calipers and micrometers
No failure should be observed when voltage in the table is
applied between the terminations for 60T1 sec., provided the
charge/discharge current is less than 50mA.
Nominal Capacitance
CU10,000pF
CF10,000pF
Test Voltage
AC575V (r.m.s.)
AC1500V (r.m.s.)
The insulation resistance should be measured with DC500T50V
and within 60T5 sec. of charging.
The capacitance/D.F. should be measured at a frequency of
1T0.2kHz and a voltage of AC1T0.2V (r.m.s.)
The capacitance measurement should be made at each step
specified in the Table.
Step
1
2
3
4
5
Temperature (D)
25T2
Min. Operating Temp.T3
25T2
Max. Operating Temp.T2
25T2
#Pretreatment
Perform a heat treatment at 150^W Y10 0D for 60T5 min. and then
let sit for 24T2 hrs. at room condition.*
As in Fig., discharge is made 50 times at 5 sec. intervals from
the capacitor (Cd) charged at DC voltage of specified.
R3
R1
10kV
V
Cd
Ct
R2
Ct: Capacitor under test Cd: 0.001µF
R1: 1,000Ω R2: 100MΩ R3: Surge resistance
Solder the capacitor to the testing jig (glass epoxy board) shown
in Fig. 1.
Then apply 10N force in the direction of the arrow. The soldering
should be done using the reflow method and should be
conducted with care so that the soldering is uniform and free of
defects such as heat shock.
10N, 10T1s
Glass Epoxy Board
Fig. 1
Solder the capacitor to the test jig (glass epoxy board).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should be
traversed in approximately 1 min. This motion should be applied
for a period of 2 hrs. in each of 3 mutually perpendicular
directions (total of 6 hrs.).
Glass Epoxy Board
Solder resist
Cu
* "Room condition" Temperature: 15 to 35D, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued on the following page.
188