GRJ43DR72J104KWJ1L Datasheet, PDF (216/221 Pages) Murata Manufacturing Co., Ltd. – Chip Monolithic Ceramic Capacitors

C02E.pdf !Note • Th!is PNDoFteca•taPlolegasisedroewadnlroaatdinegdafnrodm!thCeAwUeTbIOsiNte(ofof rMsutoraratageM, aonpuefraactitnugri,nrgatcinog.,,ltsdo.ldTehreinregf,omreo,uint’tsinsgpaencdifichaatniodnlisnga)reinstuhbisjeccatttaolocghatongpereovreonut rsmprookdiuncgtsanind/iot rmbauyrnbiengd,isectco.ntinued without advance notice. Please check with our
sales repres_•e_Tnt_ha_istiv_ce_as_tao_lor _gpr_ho_ad_suc_ot_ne_lyn_tg_yi_pn_ie_ce_ar_ls_spb_ee_cfo_ifr_ice_ao_tir_od_ne_sri_bn_eg_c. _{ause there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
10.12.20 ^{• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
Continued from the preceding page.
Land Layout to Prevent Excessive Solder
Mounting Close to a Chassis
d1
Chassis
Solder (Ground solder)
Examples
to Be Avoided
Adhesive
Base board
Land Pattern
in section
Examples of
Improvements
by the Land
Division
d2
d1<d2
Solder Resist
in section
Notice
Mounting with Leaded Components
Lead Wire Connected
to a Part Provided
with Lead Wires.
Mounting Leaded Components Later
Soldering Iron
Lead Wire of
Component to be
Connected Later.
in section
Solder Resist
Solder Resist
in section
in section
in section
2. Mounting of Chips
Thickness of adhesives applied
Keep thickness of adhesives applied (50-105µm or more)
to reinforce the adhesive contact considering the
thickness of the termination or capacitor (20-70µm) and
the land pattern (30-35µm).
Mechanical shock of the chip placer
When the positioning claws and pick-up nozzle are worn,
the load is applied to the chip while positioning is
concentrated in one position, thus causing cracks,
breakage, faulty positioning accuracy, etc.
Careful checking and maintenance are necessary to
prevent unexpected trouble.
An excessively low bottom dead point of the suction
nozzle imposes great force on the chip during mounting,
causing cracked chips. Please set the suction nozzle's
bottom dead point on the upper surface of the board.
3. Soldering
(1) Limit of losing effective area of the terminations and
conditions needed for soldering.
Depending on the conditions of the soldering
temperature and/or immersion (melting time),
effective areas may be lost in some parts of the
terminations.
To prevent this, be careful in soldering so that any
possible loss of the effective area on the terminations
will securely remain at a maximum of 25% on all
edge length A-B-C-D-A of part with A, B, C, D, shown
in the Figure below.
A
B
D
Termination
C
(2) Flux Application
An excessive amount of flux generates a large quantity of
flux gas, causing deteriorated solderability. So apply flux
thinly and evenly throughout. (A foaming system is
generally used for flow soldering.)
Flux containing too high a percentage of halide may
cause corrosion of the outer electrodes without sufficient
cleaning. Use flux with a halide content of 0.2% max.
Do not use strong acidic flux.
Do not use water-soluble flux.*
(*Water-soluble flux can be defined as non rosin type flux
including wash-type flux and non-wash-type flux.)
(3) Solder
The use of Sn-Zn based solder will deteriorate the
reliability of the MLCC.
Please contact our sales representative or product
engineers on the use of Sn-Zn based solder in advance.
Continued on the following page.
215