GRJ43DR72J104KWJ1L Datasheet, PDF (53/221 Pages) Murata Manufacturing Co., Ltd. – Chip Monolithic Ceramic Capacitors

C02E.pdf !Note • Th!is PNDoFteca•taPlolegasisedroewadnlroaatdinegdafnrodm!thCeAwUeTbIOsiNte(ofof rMsutoraratageM, aonpuefraactitnugri,nrgatcinog.,,ltsdo.ldTehreinregf,omreo,uint’tsinsgpaencdifichaatniodnlisnga)reinstuhbisjeccatttaolocghatongpereovreonut rsmprookdiuncgtsanind/iot rmbauyrnbiengd,isectco.ntinued without advance notice. Please check with our
sales repres_•e_Tnt_ha_istiv_ce_as_tao_lor _gpr_ho_ad_suc_ot_ne_lyn_tg_yi_pn_ie_ce_ar_ls_spb_ee_cfo_ifr_ice_ao_tir_od_ne_sri_bn_eg_c. _{ause there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
10.12.20 ^{• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
GRM GSRerMiesSeSrpieesciSfipceactiiofincsataionndsTaensdt MTestht oMdesth(1o)d(sN(o1t)e(N1)o-Tteyp1i)c-Tayl pInicsapleIcntsiopnection
No.
Item
Operating
1 Temperature
Range
(Note 1) These Specifications and Test Methods indicate typical inspection.
Please refer to individual specifications (our product specifications or the approval sheet).
When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).
Specifications
Temperature
Compensating Type
High Dielectric Type
Test Method
–55 to +125°C
(2P/R/S/T, 3P/R/S/T/U,
4P/R/S/T/U: –25 to +85°C)
B1, B3, F1: –25 to +85°C
R1, R7: –55 to +125°C
R6: –55 to +85°C
C8: –55 to +105°C
E4: +10 to +85°C
F5: –30 to +85°C
Reference temperature: 25°C
(2∆, 3∆, 4∆, B1, B3, F1, R1: 20°C)
2 Rated Voltage
See the previous pages.
The rated voltage is defined as the maximum voltage that may
be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, V^P-P or V^O-P,
whichever is larger, should be maintained within the rated
voltage range.
3 Appearance
No defects or abnormalities
Visual inspection
4 Dimensions
Within the specified dimensions
Using calipers (GRM02 size is based on Microscope)
5 Dielectric Strength No defects or abnormalities
No failure should be observed when 300%* of the rated voltage
(temperature compensating type) or 250% of the rated voltage
(high dielectric constant type) is applied between the
terminations for 1 to 5 seconds, provided the charge/discharge
current is less than 50mA. *200% for 500V
6
Insulation
Resistance
CV0.047µF: More than 10,000MΩ
CG0.047µF: More than 500Ω · F
C: Nominal Capacitance
The insulation resistance should be measured with a DC
voltage not exceeding the rated voltage at 20/25°C and 75%RH
max. and within 2 minutes of charging, provided the charge/
discharge current is less than 50mA.
7 Capacitance
Within the specified tolerance
30pF and over: QU1000
Q/
30pF and below:
8 Dissipation Factor
QU400+20C
(D.F.)
C: Nominal Capacitance (pF)
[R6, R7, C8]
W.V.: 100V
: 0.025 max. (CF0.068µF)
: 0.05 max. (CU0.068µF)
W.V.: 50/35/25V:
: 0.025 max.*
*GRM32D R7/R6/C8 1E106: 0.035 max.
W.V.: 16/10V: 0.035 max.
W.V.: 6.3/4V
: 0.05 max. (CF3.3µF)
: 0.1 max. (CU3.3µF)
[E4]
W.V.: 25Vmin: 0.025 max.
[F1, F5]
W.V.: 25V min.
: 0.05 max. (CF0.1µF)
: 0.09 max. (CU0.1µF)
W.V.: 16/10V: 0.125 max.
W.V.: 6.3V: 0.15 max.
The capacitance/Q/D.F. should be measured at 20/25°C at the
frequency and voltage shown in the table.
Char.
Item
∆C
to 7U, 1X
(1000pF and
below)
∆C to 7U, 1X
(more than
1000pF)
R6, R7, C8,
F5, B1, B3, F1
R6, R7, F5
(C>10µF)
E4
Frequency 1±0.1MHz 1±0.1kHz
Voltage 0.5 to 5Vrms 1±0.2Vrms
120±24Hz 1±0.1kHz
0.5±
0.5±
0.1Vrms 0.05Vrms
Continued on the following page.
51