GRJ43DR72J104KWJ1L Datasheet, PDF (200/221 Pages) Murata Manufacturing Co., Ltd. – Chip Monolithic Ceramic Capacitors

C02E.pdf !Note • Th!is PNDoFteca•taPlolegasisedroewadnlroaatdinegdafnrodm!thCeAwUeTbIOsiNte(ofof rMsutoraratageM, aonpuefraactitnugri,nrgatcinog.,,ltsdo.ldTehreinregf,omreo,uint’tsinsgpaencdifichaatniodnlisnga)reinstuhbisjeccatttaolocghatongpereovreonut rsmprookdiuncgtsanind/iot rmbauyrnbiengd,isectco.ntinued without advance notice. Please check with our
sales repres_•e_Tnt_ha_istiv_ce_as_tao_lor _gpr_ho_ad_suc_ot_ne_lyn_tg_yi_pn_ie_ce_ar_ls_spb_ee_cfo_ifr_ice_ao_tir_od_ne_sri_bn_eg_c. _{ause there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
10.12.20 ^{• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
Safety Standard Certified Type GC/GDG/GAF3/SGeBriSepseScpifeiccaiftiicoantsioannsdaTnedstTMesetthMoedthsods
Continued from the preceding page.
No.
Item
Specifications
Appearance No marking defects
Capacitance
Change
Char.
X7R
SL
Capacitance Change
Within T15%
Within T5.0% or T0.5pF
(Whichever is larger)
19
Humidity
Loading
D.F.
Q
Char.
X7R
SL
Specification
D.F.V0.05
QU275W5/2C*² (CF30pF)
QU350
(CU30pF)
I.R.
Dielectric
Strength
More than 3,000MΩ
In accordance with item No.4
Test Method
Before this test, the test shown in the following is performed.
·Item 11 Adhesive Strength of Termination (apply force is 5N)
·Item 13 Deflection
Apply the rated voltage at 40T2D and relative humidity of 90 to
95% for 500Y ^{W20 4}hrs. Remove and let sit for 24T2 hrs. at room
condition,*¹ then measure.
#Pretreatment for X7R char.
Perform a heat treatment at 150^W Y10 0 D for 60T5 min. and then
let sit for 24T2 hrs. at room condition.*¹
The capacitor should be individually wrapped in at least one but
not more than two complete layers of cheesecloth. The
capacitor should be subjected to 20 discharges. The interval
between successive discharges should be 5 sec. The UAC
should be maintained for 2 min. after the last discharge.
S1
F L1
L2
R
C1 C2
C3 Cx
Ct
Ut
Tr ^{S2 UAC L3}
L4
20
Active
Flammability
The cheesecloth should not be on fire.
Oscilloscope
C1,2 : 1µFT10%
C3 : 0.033µFT5% 10kV
L1 to 4 : 1.5mHT20% 16A Rod core choke
Ct : 3µFT5% 10kV
R : 100ΩT2%
Cx : Capacitor under test UAC : URT5%
F : Fuse, Rated 16A
UR : Rated Voltage
Ut : Voltage applied to Ct
Ux
Ui
Type
GD, GB
GC, GF
Ui
2.5kV
5kV
21
Passive
Flammability
The burning time should not exceed 30 sec.
The tissue paper should not ignite.
time
The capacitor under test should be held in the flame in the
position which best promotes burning. Each specimen should
be exposed to the flame only once. Time of exposure to flame:
30 sec.
Length of flame : 12T1mm
Gas burner : Length 35mm min.
Inside Dia. 0.5T0.1mm
Outside Dia. 0.9mm max.
Gas
: Butane gas Purity 95% min.
Test Specimen
45°
*1 "Room condition" Temperature: 15 to 35D, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
*2 "C" expresses nominal capacitance value (pF).
Tissue
About 10mm Thick Board
199