GRJ43DR72J104KWJ1L Datasheet, PDF (59/221 Pages) Murata Manufacturing Co., Ltd. – Chip Monolithic Ceramic Capacitors

C02E.pdf !Note • Th!is PNDoFteca•taPlolegasisedroewadnlroaatdinegdafnrodm!thCeAwUeTbIOsiNte(ofof rMsutoraratageM, aonpuefraactitnugri,nrgatcinog.,,ltsdo.ldTehreinregf,omreo,uint’tsinsgpaencdifichaatniodnlisnga)reinstuhbisjeccatttaolocghatongpereovreonut rsmprookdiuncgtsanind/iot rmbauyrnbiengd,isectco.ntinued without advance notice. Please check with our
sales repres_•e_Tnt_ha_istiv_ce_as_tao_lor _gpr_ho_ad_suc_ot_ne_lyn_tg_yi_pn_ie_ce_ar_ls_spb_ee_cfo_ifr_ice_ao_tir_od_ne_sri_bn_eg_c. _{ause there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
10.12.20 ^{• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
GRM GSRerMiesSeSrpieesciSfipceactiiofincsataionndsTaensdt MTestht oMdesth(2o)d(sN(o2t)e(N1)o-Tteyp1i)c-Tayl pInicsapleIcntsiopnection
(Note 1) These Specifications and Test Methods indicate typical inspection.
Please refer to individual specifications (our product specifications or the approval sheet).
When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).
No.
Item
Specifications
Test Method
Operating
1 Temperature
Range
B1, B3, F1: –25 to +85°C
R1, R7, C7, D7, E7: –55 to +125°C
C6, R6: –55 to +85°C
F5: –30 to +85°C
C8, D8: –55 to +105°C,
2 Rated Voltage
See the previous pages.
3 Appearance
4 Dimensions
No defects or abnormalities
Within the specified dimensions
5 Dielectric Strength No defects or abnormalities
6
Insulation
Resistance
More than 50Ω · F
7 Capacitance
Within the specified tolerance
*Table 1
GRM022 B3/R6
GRM155 B3/R6
GRM185 B3/R6
GRM185 C8/D7
GRM188 B3/R6
GRM188 R7/C8
GRM188 B3/R6
GRM219 B3/R6
GRM219 C8
GRM219 B3/R6
GRM21B B3/R6
GRM21B R7/C8
GRM319 B3/R6
1A 681 to 103
1A 124 to 105
1C/1A 105
1A
105
1C/1A 225
1A
225
1A
335
1C/1A 475
1A
475
1A
106
1C/1A 106
1A
106
1C/1A 106
B1, B3, R1, *R6, *R7, C7, C8, E7, D7: 0.1 max.
C6: 0.125 max.
8
Dissipation Factor
(D.F.)
D8: 0.15 max.
F1, F5: 0.2 max.
*GRM31CR71E106: 0.125 max.
GRM31CR6 0J/0G 107: 0.15 max.
Reference temperature: 25°C
(B1, B3, R1, F1: 20°C)
The rated voltage is defined as the maximum voltage that may
be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, V^P-P or V^O-P,
whichever is larger, should be maintained within the rated
voltage range.
Visual inspection
Using calipers (GRM02 size is based on Microscope)
No failure should be observed when 250% of the rated voltage
is applied between the terminations for 1 to 5 seconds,
provided the charge/discharge current is less than 50mA.
The insulation resistance should be measured with a DC voltage
not exceeding the rated voltage at reference temperature and
75%RH max. and within 1 minutes of charging, provided the
charge/discharge current is less than 50mA.
The capacitance/D.F. should be measured at reference
temperature at the measuring frequency and voltage shown in
the table.
Nominal Capacitance
CV10µF (10V min.)*
CV10µF (6.3V max.)
CG10µF
*For items in Table1
Measuring Frequency
1±0.1kHz
1±0.1kHz
120±24Hz
1±0.1kHz
Measuring Voltage
1.0±0.2Vrms
0.5±0.1Vrms
0.5±0.1Vrms
0.5±0.1Vrms
GRM188C80E106:
Perform a heat treatment at 150+0/-10°C for one hour and then
set for 24±2 hours at room temperature.
Continued on the following page.
57