GRJ43DR72J104KWJ1L Datasheet, PDF (179/221 Pages) Murata Manufacturing Co., Ltd. – Chip Monolithic Ceramic Capacitors

C02E.pdf !Note • Th!is PNDoFteca•taPlolegasisedroewadnlroaatdinegdafnrodm!thCeAwUeTbIOsiNte(ofof rMsutoraratageM, aonpuefraactitnugri,nrgatcinog.,,ltsdo.ldTehreinregf,omreo,uint’tsinsgpaencdifichaatniodnlisnga)reinstuhbisjeccatttaolocghatongpereovreonut rsmprookdiuncgtsanind/iot rmbauyrnbiengd,isectco.ntinued without advance notice. Please check with our
sales repres_•e_Tnt_ha_istiv_ce_as_tao_lor _gpr_ho_ad_suc_ot_ne_lyn_tg_yi_pn_ie_ce_ar_ls_spb_ee_cfo_ifr_ice_ao_tir_od_ne_sri_bn_eg_c. _{ause there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
10.12.20 ^{• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.}
GORnlMy /fDoCr 3L.C15DkBVaScekrliegshtSIpnevceirftiecratCioirncsuiatnSdpTeceisfticMateitohnosdasnd Test Methods
Continued from the preceding page.
No.
Item
Specifications
12
Solderability of
Termination
75% of the terminations are to be soldered evenly
and continuously.
Appearance No marking defects
Capacitance
Change
13
Resistance
to Soldering
Q
Heat
I.R.
Within T2.5%
1,000 min.
More than 10,000MΩ
Dielectric
Strength
In accordance with item No.4
Appearance No marking defects
Capacitance
Change
Within T2.5%
Q
1,000 min.
I.R.
More than 10,000MΩ
14
Temperature
Cycle
Test Method
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Immerse in
solder solution for 2T0.5 sec.
Immersing speed: 25T2.5mm/s
Temp. of solder: 245T5°C Lead Free Solder (Sn-3.0Ag-0.5Cu)
235T5°C H60A or H63A Eutectic Solder
Preheat the capacitor as in table.
Immerse the capacitor in solder solution at 260T5D for 10T1 sec.
Let sit at room condition* for 24T2 hrs., then measure.
#Immersing speed: 25T2.5mm/s
*Preheating
Step
1
2
Temperature
100 to 120D
170 to 200D
Time
1 min.
1 min.
Fix the capacitor to the supporting jig (glass epoxy board) shown
in Fig. 4.
Perform the 5 cycles according to the 4 heat treatments listed in
the following table.
Let sit for 24T2 hrs. at room condition,* then measure.
Step
1
2
3
4
Temperature (D)
Min. Operating Temp.T3
Room Temp.
Max. Operating Temp.T2
Room Temp.
Time (min.)
30T3
2 to 3
30T3
2 to 3
Dielectric
Strength
In accordance with item No.4
Glass Epoxy Board
Fig. 4
Solder resist
Cu
Appearance No marking defects
Capacitance
Humidity ^Change
15 (Steady Q
State) _I.R.
Dielectric
Strength
Within T5.0%
350 min.
More than 1,000MΩ
In accordance with item No.4
Let the capacitor sit at 40T2D and relative humidity of 90 to 95%
for 500^W Y²⁴⁰hrs.
Remove and let sit for 24T2 hrs. at room condition,* then
measure.
Appearance No marking defects
16 Life
Capacitance
Change
Q
I.R.
Dielectric
Strength
Within T3.0%
350 min.
More than 1,000MΩ
In accordance with item No.4
Apply 120% of the rated voltage for 1,000^W Y⁴⁸ 0 hrs. at maximum
operating temperature T3D.
Remove and let sit for 24T2 hrs. at room condition,* then
measure.
The charge/discharge current is less than 50mA.
* "Room condition" Temperature: 15 to 35D, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
178