PIC18F-LF1XK50 Datasheet, PDF (59/420 Pages) Microchip Technology – 20-Pin USB Flash Microcontrollers

PIC18F1XK50/PIC18LF1XK50
EXAMPLE 4-3:
PROGRAM_MEMORY
Required
Sequence
WRITING TO FLASH PROGRAM MEMORY (CONTINUED)
DECFSZ COUNTER
; loop until holding registers are full
BRA
WRITE_WORD_TO_HREGS
BSF
BCF
BSF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
DCFSZ
BRA
BSF
BCF
EECON1, EEPGD
EECON1, CFGS
EECON1, WREN
INTCON, GIE
55h
EECON2
0AAh
EECON2
EECON1, WR
COUNTER2
WRITE_BYTE_TO_HREGS
INTCON, GIE
EECON1, WREN
; point to Flash program memory
; access Flash program memory
; enable write to memory
; disable interrupts
; write 55h
; write 0AAh
; start program (CPU stall)
; repeat for remaining write blocks
;
; re-enable interrupts
; disable write to memory
4.5.2 WRITE VERIFY
Depending on the application, good programming
practice may dictate that the value written to the
memory should be verified against the original value.
This should be used in applications where excessive
writes can stress bits near the specification limit.
4.5.3
UNEXPECTED TERMINATION OF
WRITE OPERATION
If a write is terminated by an unplanned event, such as
loss of power or an unexpected Reset, the memory
location just programmed should be verified and
reprogrammed if needed. If the write operation is
interrupted by a MCLR Reset or a WDT Time-out Reset
during normal operation, the WRERR bit will be set
which the user can check to decide whether a rewrite
of the location(s) is needed.
4.5.4
PROTECTION AGAINST
SPURIOUS WRITES
To protect against spurious writes to Flash program
memory, the write initiate sequence must also be
followed. See Section 24.0 “Special Features of the
CPU” for more detail.
4.6 Flash Program Operation During
Code Protection
See Section 24.3 “Program Verification and Code
Protection” for details on code protection of Flash
program memory.
TABLE 4-3: REGISTERS ASSOCIATED WITH PROGRAM FLASH MEMORY
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values on
page
TBLPTRU
—
—
bit 21 Program Memory Table Pointer Upper Byte (TBLPTR<20:16>) 285
TBPLTRH Program Memory Table Pointer High Byte (TBLPTR<15:8>)
285
TBLPTRL Program Memory Table Pointer Low Byte (TBLPTR<7:0>)
285
TABLAT Program Memory Table Latch
285
INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RABIE TMR0IF INT0IF RABIF
285
EECON2 EEPROM Control Register 2 (not a physical register)
287
EECON1 EEPGD CFGS
—
FREE WRERR WREN
WR
RD
287
IPR2
OSCFIP C1IP C2IP EEIP
BCLIP USBIP TMR3IP
—
288
PIR2
OSCFIF C1IF C2IF EEIF
BCLIF USBIF TMR3IF
—
288
PIE2
OSCFIE C1IE C2IE EEIE
BCLIE USBIE TMR3IE
—
288
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used during Flash/EEPROM access.
 2010 Microchip Technology Inc.
Preliminary
DS41350E-page 59