PIC32MX5XX_11 Datasheet, PDF (248/256 Pages) Microchip Technology – High-Performance, USB, CAN and Ethernet 32-bit Flash Microcontrollers

PIC32MX5XX/6XX/7XX
TABLE B-4: SECTION UPDATES (CONTINUED)
Section Name
Update Description
7.0 “Interrupt Controller”
8.0 “Oscillator Configuration”
16.0 “Output Compare”
24.0 “Ethernet Controller”
26.0 “Comparator Voltage Reference
(CVREF)”
28.0 “Special Features”
• Updated the following Interrupt Sources in Table 7-1:
- Changed IC2AM – I2C4 Master Event to: IC4M – I2C4 Master Event
- Changed IC3AM – I2C5 Master Event to: IC5M – I2C4 Master Event
- Changed U1E – UART1A Error to: U1E – UART1 Error
- Changed U4E – UART1B Error to: U4E – UART4 Error
- Changed U1RX – UART1A Receiver to: U1RX – UART1 Receiver
- Changed U4RX – UART1B Receiver to: U4RX – UART4 Receiver
- Changed U1TX – UART1A Transmitter to: U1TX – UART1 Transmitter
- Changed U4TX – UART1B Transmitter to: U4TX – UART4 Transmitter
- Changed U6E – UART2B Error to: U6E – UART6 Error
- Changed U6RX – UART2B Receiver to: U6RX – UART6 Receiver
- Changed U6TX – UART2B Transmitter to: U6TX – UART6 Transmitter
- Changed U5E – UART3B Error to: U5E – UART5 Error
- Changed U5RX – UART3B Receiver to: U5RX – UART5 Receiver
- Changed U5TX – UART3B Transmitter to: U5TX – UART5 Transmitter
Updated Figure 8-1
Updated Figure 16-1
Added a note on using the Ethernet controller pins (see note above
Table 24-3)
Updated the note in Figure 26-1
Updated the bit description for bit 10 in Register 28-2
31.0 “Electrical Characteristics”
Added notes 1 and 2 to Register 28-4
Updated the Absolute Maximum Ratings:
• Voltage on any 5V tolerant pin with respect to VSS when VDD < 2.3V -
0.3V to +3.6V was updated
• Voltage on VBUS with respect to VSS - 0.3V to +5.5V was added
Updated the maximum value of DC16 as 2.1 in Table 31-4
Updated the Typical values for the following parameters: DC20b, DC20c,
DC21c, DC22c and DC23c (see Table 31-5)
Updated Table 31-11:
• Removed the following DC Characteristics: Programming temperature
0°C ≤TA ≤+70°C (25°C recommended)
• Updated the Minimum value for the Parameter number D131 as 2.3
• Removed the Conditions for the following Parameter numbers: D130,
D131, D132, D135, D136 and D137
• Updated the condition for the parameter number D130a and D132a
Updated the Minimum, Typical and Maximum values for parameter D305
in Table 31-13
Added note 2 to Table 31-18
Updated the Minimum and Maximum values for parameter F20b (see
Table 31-19)
Updated the following figures:
Appendix A: “Migrating from
PIC32MX3XX/4XX to PIC32MX5XX/
6XX/7XX Devices”
• Figure 31-4
• Figure 31-9
• Figure 31-19
• Figure 31-20
Removed the A.3 Pin Assignments sub-section.
DS61156G-page 248
© 2009-2011 Microchip Technology Inc.