DS892 Datasheet, PDF (3/79 Pages) Xilinx, Inc – DC and AC Switching Characteristics

Kintex UltraScale FPGAs Data Sheet: DC and AC Switching Characteristics
Table 1: Absolute Maximum Ratings⁽¹⁾ (Cont’d)
Symbol
Description
Min
Max
Units
T_j
Maximum junction temperature⁽¹⁰⁾
–
125
°C
Notes:
1. Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are
stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under
Operating Conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time might
affect device reliability.
2. V_{CCINT_IO} must be connected to V_CCINT.
3. V_{CCAUX_IO} must be connected to V_CCAUX.
4. The lower absolute voltage specification always applies.
5. If V_CCO is 3.3V, the maximum voltage is 3.4V.
6. For I/O operation, see the UltraScale Architecture SelectIO Resources User Guide (UG571).
7. The maximum limit applied to DC signals. For maximum undershoot and overshoot AC specifications, see Table 4 and
Table 5.
8. See Table 12 for TMDS_33 specifications.
9. For more information on supported GTH or GTY transceiver terminations see the UltraScale Architecture GTH Transceiver
User Guide (UG576) or the UltraScale Architecture GTY Transceiver User Guide (UG578).
10. For soldering guidelines and thermal considerations, see the UltraScale and UltraScale+ FPGAs Packaging and Pinout
Specifications (UG575).
Table 2: Recommended Operating Conditions⁽¹⁾⁽²⁾
Symbol
Description
Min
FPGA Logic
Internal supply voltage
0.922
V_CCINT
For -1L (0.90V) devices: internal supply voltage
For -3 (1.0V only) devices: internal supply voltage
0.880
0.970
Internal supply voltage for the I/O banks
0.922
V_{CCINT_IO(3)}
For -1L (0.90V) devices: internal supply voltage for the I/O
banks
For -3 (1.0V only) devices: internal supply voltage for the
I/O banks
0.880
0.970
V_CCBRAM
Block RAM supply voltage
For -3 (1.0V only) devices: block RAM supply voltage
0.922
0.970
V_CCAUX
V_CCO(4)(5)
Auxiliary supply voltage
Supply voltage for HR I/O banks
Supply voltage for HP I/O banks
1.746
1.140
0.950
V_{CCAUX_IO(6)}
V_IN(7)
Auxiliary I/O supply voltage
I/O input voltage
dI/iOffeirnepnuttiavl ^{oIl/tOagseta(nwdhaerndsVeC}x^Cc^Oe=pt3T.M3VD)Sf_o3r3V^(8R)E.^{F and}
1.746
–0.200
–
I_IN(9)
Maximum current through any pin in a powered or
unpowered bank when forward biasing the clamp diode.
–
V_BATT(10)
Battery voltage
GTH and GTY Transceivers
1.000
V_MGTAVCC(11)
V_MGTAVTT(11)
V_{MGTVCCAUX(11)}
Analog supply voltage for the GTH and GTY transceivers⁽¹⁰⁾
Analog supply voltage for the GTH and GTY transmitter and
receiver termination circuits
Auxiliary analog QPLL voltage supply for the transceivers
0.970
1.170
1.750
Typ
Max
Units
0.950
0.979
V
0.900
0.920
V
1.000
1.030
V
0.950
0.979
V
0.900
0.920
V
1.000
1.030
V
0.950
0.979
V
1.000
1.030
V
1.800
1.854
V
–
3.400
V
–
1.890
V
1.800
1.854
V
–
V_CCO + 0.200 V
0.400
2.625
V
–
10.000
mA
–
1.890
V
1.000
1.030
V
1.200
1.230
V
1.800
1.850
V
DS892 (v1.12) April 1, 2016
Product Specification
www.xilinx.com
Send Feedback
3