PIC16F1847_13 Datasheet, PDF (353/440 Pages) Microchip Technology – 18/20/28-Pin Flash Microcontrollers with XLP Technology

PIC16(L)F1847
30.3 DC Characteristics: Power-Down Currents (IPD)
PIC16LF1847
PIC16F1847
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param.
No.
Device Characteristics
Min.
Typ†
Max.
+85°C
Max.
+125°C
Units
VDD
Conditions
Note
Power-down Base Current (IPD) (Note 2)
D022
— 0.02 1.0
2.4
A
1.8 WDT, BOR and T1OSC disabled,
— 0.03 1.5
3.0
A
3.0 ^{all Peripherals Inactive}
D022
—
15
35
—
18
40
44
A
1.8 WDT, BOR and T1OSC disabled,
48
A
3.0 ^{all Peripherals Inactive}
—
19
45
65
A
5.0
D023
—
0.3
1
3
A
1.8 LPWDT Current (Note 1)
—
0.8
2
4
A
3.0
D023
—
16
35
44
A
1.8 LPWDT Current (Note 1)
—
19
40
48
A
3.0
D023A
—
20
45
—
20
25
—
21
27
65
A
5.0
35
A
1.8 FVR current
37
A
3.0
D023A
D024
—
40
62
65
A
1.8 FVR current
—
50
72
75
A
3.0
—
80
115
120
A
5.0
—
8.0
14
16
A
3.0 BOR Current (Note 1)
D024
D025
—
24
47
50
A
3.0 BOR Current (Note 1)
—
29
55
70
A
5.0
— 0.65 3.5
4.0
A
1.8 T1OSC Current (Note 1)
D025
D026
D026
—
2.3
5.0
6.0
A
3.0
—
19
39
45
A
1.8 T1OSC Current (Note 1)
—
21
43
59
A
3.0
—
28
55
75
A
5.0
— 0.03 1.5
3.0
A
1.8 ADC Current (Note 1, 3),
— 0.07 2.0
3.5
A
3.0 ^{no conversion in progress}
—
18
38
—
20
43
45
A
1.8 ADC Current (Note 1, 3),
49
A
3.0 ^{no conversion in progress}
—
22
46
65
A
5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: ADC oscillator source is FRC.
 2011-2013 Microchip Technology Inc.
Preliminary
DS40001453D-page 353