PIC16F1847_13 Datasheet, PDF (350/440 Pages) Microchip Technology – 18/20/28-Pin Flash Microcontrollers with XLP Technology

PIC16(L)F1847
30.2 DC Characteristics: Supply Current (IDD)
PIC16LF1847
PIC16F1847
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param.
No.
Device
Characteristics
Min. Typ† Max. Units
VDD
Conditions
Note
Supply Current (IDD) (Note 1, 2)
D010
—
9.5
14
A
1.8 _{FOSC = 32 kHz}
—
12.5
17
A
3.0 ^{LP Oscillator}
-40°C  TA +85°C
D010
—
22
29
A
1.8 FOSC = 32 kHz
—
27
35
A
3.0 ^{LP Oscillator}
-40°C  TA +85°C
—
30
38
A
5.0
D010A
—
9.5
14
A
1.8 FOSC = 32 kHz
—
12.5
17
A
3.0 ^{LP Oscillator}
-40°C  TA +125°C
D010A
—
22
29
A
1.8 FOSC = 32 kHz
—
27
35
A
3.0 ^{LP Oscillator}
-40°C  TA +125°C
—
30
38
A
5.0
D011
—
105
110
A
—
160
190
A
1.8 FOSC = 1 MHz
3.0 ^{XT Oscillator}
D011
—
132
154
A
—
186
220
A
1.8 FOSC = 1 MHz
3.0 ^{XT Oscillator}
—
216
290
A
5.0
D012
—
264
370
A
—
491
620
A
1.8 FOSC = 4 MHz
3.0 ^{XT Oscillator}
D012
—
285
300
A
—
408
600
A
1.8 FOSC = 4 MHz
3.0 ^{XT Oscillator}
—
490
700
A
5.0
D013
—
55
160
A
1.8 FOSC = 1 MHz
—
90
230
A
3.0 ^{EC Oscillator}
Medium-power mode
D013
—
75
95
A
—
116
130
A
—
145
185
A
1.8 FOSC = 1 MHz
3.0 ^{EC Oscillator}
Medium-power mode
5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: 8 MHz internal oscillator with 4x PLL enabled.
4: 8 MHz crystal oscillator with 4x PLL enabled.
5: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in k
DS40001453D-page 350
Preliminary
 2011-2013 Microchip Technology Inc.