PIC17C7XX_13 Datasheet, PDF (245/306 Pages) Microchip Technology – High-Performance 8-bit CMOS EPROM Microcontrollers with 10-bit A/D

PIC17C7XX
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  TA  +125°C for extended
-40°C  TA  +85°C for industrial
0°C  TA  +70°C for commercial
Operating voltage VDD range as described in Section 20.1
Param.
No.
Sym
Characteristic
Min
Typ† Max Units
Conditions
Input Leakage Current
(Notes 2, 3)
D060 IIL
I/O ports (except RA2, RA3)
–
–
1
A Vss VPIN VDD,
I/O Pin (in digital mode) at
hi-impedance PORTB
weak pull-ups disabled
D061
MCLR, TEST
–
–
2
A VPIN =Vss orVPIN =VDD
D062
RA2, RA3
2
A Vss VRA2, VRA3  12V
D063
OSC1 (EC, RC modes)
–
–
1
A Vss VPIN VDD
D063B
OSC1 (XT, LF modes)
–
–
VPIN
A RF  1 M
D064
MCLR, TEST
–
–
25
A VMCLR = VPP = 12V
(when not programming)
D070 IPURB PORTB Weak Pull-up Current
85
Output Low Voltage
130
260
A VPIN = VSS, RBPU = 0
4.5V VDD 5.5V
D080 VOL I/O ports
D081
with TTL buffer
IOL = VDD/1.250 mA
–
–
0.1VDD V 4.5V  VDD  5.5V
–
–
0.1VDD V VDD  3.0V
–
–
0.4
V IOL = 6 mA, VDD = 4.5V
(Note 6)
D082
RA2 and RA3
–
–
3.0
V IOL = 60.0 mA, VDD = 5.5V
–
–
0.6
V IOL = 60.0 mA, VDD = 4.5V
D083
D084
OSC2/CLKOUT
(RC and EC osc modes)
–
–
0.4
V IOL = 1 mA, VDD = 4.5V
–
–
0.1VDD V IOL = VDD/5 mA
(PIC17LC7XX only)
Output High Voltage (Note 3)
D090 VOH
D091
I/O ports (except RA2 and
RA3)
with TTL buffer
0.9VDD
–
0.9VDD
–
2.4
–
IOH = -VDD/2.5 mA
–
V 4.5V  VDD  5.5V
–
V VDD  3.0V
–
V IOH = -6.0 mA, VDD = 4.5V
(Note 6)
D093
D094
OSC2/CLKOUT
(RC and EC osc modes)
2.4
–
0.9VDD
–
–
V IOH = -5 mA, VDD = 4.5V
–
V IOH = -VDD/5 mA
(PIC17LC7XX only)
† Data in “Typ” column is at 5V, 25C unless otherwise stated.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC17CXXX devices be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. Higher leakage
current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
4: These specifications are for the programming of the on-chip program memory EPROM through the use of the
table write instructions. The complete programming specifications can be found in: PIC17C7XX Programming
Specifications (Literature number DS TBD).
5: The MCLR/VPP pin may be kept in this range at times other than programming, but is not recommended.
6: For TTL buffers, the better of the two specifications may be used.
 1998-2013 Microchip Technology Inc.
DS30289C-page 245