PIC18F2480_09 Datasheet, PDF (426/490 Pages) Microchip Technology – 28/40/44-Pin Enhanced Flash Microcontrollers with ECAN Technology, 10-Bit A/D and nanoWatt Technology

PIC18F2480/2580/4480/4580
28.2 DC Characteristics: Power-Down and Supply Current
PIC18F2480/2580/4480/4580 (Industrial, Extended)
PIC18LF2480/2580/4480/4580 (Industrial) (Continued)
PIC18LF2480/2580/4480/4580
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2480/2580/4480/4580
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
Device
Typ Max Units
Conditions
Supply Current (IDD)^(2,3)
PIC18LF2X80/4X80 1.5 2.1 mA
-40°C
1.5 2.1 mA
+25°C
VDD = 2.0V
1.5 2.1 mA
+85°C
PIC18LF2X80/4X80 2.4 3.3 mA
2.4 3.3 mA
2.4 3.3 mA
All devices 4.4 5.3 mA
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 4 MHz
(RC_RUN mode,
Internal oscillator source)
4.4 5.3 mA
4.4 5.3 mA
+25°C
+85°C
VDD = 5.0V
Extended devices only 9.2 11 mA
+125°C
PIC18LF2X80/4X80 6.1 8.4 μA
-40°C
6.7 8.4 μA
+25°C
VDD = 2.0V
7.4 21 μA
+85°C
PIC18LF2X80/4X80 9.6 12 μA
11 12 μA
12 33 μA
All devices 20 28 μA
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 31 kHz
(RC_IDLE mode,
Internal oscillator source)
22 28 μA
24 55 μA
+25°C
+85°C
VDD = 5.0V
Extended devices only 84 200 μA
+125°C
Legend: Shading of rows is to assist in readability of the table.
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the
part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta current
disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the
current consumption.The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula, Ir = VDD/2REXT (mA), with REXT in kΩ.
4: Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
DS39637D-page 426
© 2009 Microchip Technology Inc.