TLK105_16 Datasheet, PDF (74/104 Pages) Texas Instruments – TLK105 TLK106 Industrial Temp, Single Port 10/100Mbs Ethernet Physical Layer

TLK105
TLK106
SLLSEB8C – AUGUST 2012 – REVISED APRIL 2016
www.ti.com
8.8.10 Cable Diagnostic Amplitude Results Register 3 (CDARR3)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-48. Cable Diagnostic Amplitude Results Register 3 (CDARR3), address 0x0187
BIT
BIT NAME
15 RESERVED
14:8 TPRD Peak
Amplitude 1
7 RESERVED
6:0 TPTD Peak
Amplitude 5
DEFAULT
0, RO
000 0000, RO
0, RO
000 0000, RO
DESCRIPTION
RESERVED: Writes ignored, read as 0.
Amplitude of the First peak discovered by the TDR mechanism on Receive Channel (TPRD).
The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR3 (0x182)
RESERVED: Writes ignored, read as 0.
Amplitude of the Fifth peak discovered by the TDR mechanism on Transmit Channel (TPTD).
The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR3 (0x182)
8.8.11 Cable Diagnostic Amplitude Results Register 4 (CDARR4)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-49. Cable Diagnostic Amplitude Results Register 4 (CDARR4), address 0x0188
BIT
BIT NAME
15 RESERVED
14:8 TPRD Peak
Amplitude 3
7 RESERVED
6:0 TPRD Peak
Amplitude 2
DEFAULT
DESCRIPTION
0, RO
RESERVED: Writes ignored, read as 0.
000 0000, RO Amplitude of the Third peak discovered by the TDR mechanism on Receive Channel (TPRD).
The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR4 (0x183)
0, RO
RESERVED: Writes ignored, read as 0.
000 0000, RO Amplitude of the Second peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR4 (0x183)
8.8.12 Cable Diagnostic Amplitude Results Register 5 (CDARR5)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-50. Cable Diagnostic Amplitude Results Register 5 (CDARR5), address 0x0189
BIT
BIT NAME
15 RESERVED
14:8 TPRD Peak
Amplitude 5
7 RESERVED
6:0 TPRD Peak
Amplitude 4
DEFAULT
DESCRIPTION
0, RO
RESERVED: Writes ignored, read as 0.
000 0000, RO Amplitude of the Fifth peak discovered by the TDR mechanism on Receive Channel (TPRD).
The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR4 (0x184)
0, RO
RESERVED: Writes ignored, read as 0.
000 0000, RO Amplitude of the Fourth peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR4 (0x184)
74
Register Block
Copyright © 2012–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106