LM3S5762 Datasheet, PDF (399/841 Pages) Texas Instruments – Stellaris® LM3S5762 Microcontroller

Stellaris® LM3S5762 Microcontroller
pin placements for these GP Timer signals. The AFSEL bit in the GPIO Alternate Function Select
(GPIOAFSEL) register (page 370) should be set to choose the GP Timer function. For more information
on configuring GPIOs, see “General-Purpose Input/Outputs (GPIOs)” on page 350.
Table 10-2. General-Purpose Timers Signals (64LQFP)
Pin Name
Pin Number Pin Type Buffer Type^a Description
CCP0
47
I/O
TTL
Capture/Compare/PWM 0.
CCP1
56
I/O
TTL
Capture/Compare/PWM 1.
CCP2
11
I/O
TTL
Capture/Compare/PWM 2.
CCP3
8
I/O
TTL
Capture/Compare/PWM 3.
CCP4
16
I/O
TTL
Capture/Compare/PWM 4.
a. The TTL designation indicates the pin has TTL-compatible voltage levels.
10.3
Functional Description
The main components of each GPTM block are two free-running 16-bit up/down counters (referred
to as TimerA and TimerB), two 16-bit match registers, and two 16-bit load/initialization registers and
their associated control functions. The exact functionality of each GPTM is controlled by software
and configured through the register interface.
Software configures the GPTM using the GPTM Configuration (GPTMCFG) register (see page 409),
the GPTM TimerA Mode (GPTMTAMR) register (see page 410), and the GPTM TimerB Mode
(GPTMTBMR) register (see page 412). When in one of the 32-bit modes, the timer can only act as
a 32-bit timer. However, when configured in 16-bit mode, the GPTM can have its two 16-bit timers
configured in any combination of the 16-bit modes.
10.3.1
GPTM Reset Conditions
After reset has been applied to the GPTM module, the module is in an inactive state, and all control
registers are cleared and in their default states. Counters TimerA and TimerB are initialized to
0xFFFF, along with their corresponding load registers: the GPTM TimerA Interval Load
(GPTMTAILR) register (see page 423) and the GPTM TimerB Interval Load (GPTMTBILR) register
(see page 424). The prescale counters are initialized to 0x00: the GPTM TimerA Prescale
(GPTMTAPR) register (see page 427) and the GPTM TimerB Prescale (GPTMTBPR) register (see
page 428).
10.3.2
32-Bit Timer Operating Modes
This section describes the three GPTM 32-bit timer modes (One-Shot, Periodic, and RTC) and their
configuration.
The GPTM is placed into 32-bit mode by writing a 0 (One-Shot/Periodic 32-bit timer mode) or a 1
(RTC mode) to the GPTM Configuration (GPTMCFG) register. In both configurations, certain GPTM
registers are concatenated to form pseudo 32-bit registers. These registers include:
■ GPTM TimerA Interval Load (GPTMTAILR) register [15:0], see page 423
■ GPTM TimerB Interval Load (GPTMTBILR) register [15:0], see page 424
■ GPTM TimerA (GPTMTAR) register [15:0], see page 429
■ GPTM TimerB (GPTMTBR) register [15:0], see page 430
November 17, 2011
399
Texas Instruments-Production Data