RX24U Datasheet, PDF (69/131 Pages) Renesas Technology Corp – 32-bit RXv2 CPU core

RX24U Group
5. Electrical Characteristics
5.1 Absolute Maximum Ratings
5. Electrical Characteristics
Table 5.1
Absolute Maximum Ratings
Conditions: VSS = AVSS0 = AVSS1 = AVSS2 = VREFL0 = VREFL1 = VREFL2 = 0 V
Item
Power supply voltage
Input voltage
Port 4, port 5, port 6
Except for port 4, port 5, port 6
and ports for 5 V tolerant*¹
Ports for 5 V tolerant*¹
Symbol
VCC
V_in
Value
Unit
–0.3 to +6.5
V
–0.3 to AVCC2 + 0.3
V
–0.3 to VCC + 0.3
V
–0.3 to +6.5
V
Reference power supply voltage
VREFH0
–0.3 to AVCC0 + 0.3
V
Analog power supply voltage
VREFH1
VREFH2
AVCC0, AVCC1,
AVCC2
–0.3 to AVCC1 + 0.3
V
–0.3 to AVCC2 + 0.3
V
–0.3 to +6.5
V
Analog input
voltage
When AN000 to AN003,
AN100 to AN103,
AN200 to AN211 used
When AN016, AN116 used
Reference ground for PGA gain setting resistor
Operating temperature
Storage temperature
V_AN
PGAVSS0
PGAVSS1
T_opr
T_stg
–0.3 to AVCC2 + 0.3
V
–0.3 to VCC + 0.3
–0.3 to AVCC0 + 0.3
V
–0.3 to AVCC1 + 0.3
V
–40 to +85
°C
–55 to +125
°C
Caution: Permanent damage to the MCU may result if absolute maximum ratings are exceeded.
To preclude any malfunctions due to noise interference, insert capacitors of high frequency characteristics between the VCC and
VSS pins, between the AVCC0 and AVSS0 pins, between the AVCC1 and AVSS1 pins, between the AVCC2 and AVSS2 pins,
between the VREFH0 and VREFL0 pins, between the VREFH1 and VREFL1 pins, and between the VREFH2 and VREFL2 pins.
Place capacitors of about 0.1 μF as close as possible to every power supply pin and use the shortest and heaviest possible
traces.
Connect the VCL pin to a VSS pin via a 4.7 μF capacitor. The capacitor must be placed close to the pin.
Do not input signals or an I/O pull-up power supply to ports other than 5 V tolerant ports while the device is not powered.
The current injection that results from input of such a signal or I/O pull-up may cause malfunction and the abnormal current that
passes in the device at this time may cause degradation of internal elements.
Even if –0.3 to +6.5 V is input to 5 V tolerant ports, it will not cause problems such as damage to the MCU.
Note 1. Ports B1 and B2 are 5 V tolerant.
Table 5.2
Recommended Operating Voltage Conditions
Item
Symbol
Power supply voltages
VCC^{*1, *2}
VSS
Analog power supply voltages
AVCC0, AVCC1,
AVCC2^{*1, *2},
VREFH0, VREFH1,
VREFH2
AVSS0, AVSS1,
AVSS2, VREFL0,
VREFL1, VREFL2
Conditions
Min.
Typ.
Max.
Unit
2.7
—
5.5
V
—
0
—
VCC
—
5.5
V
—
0
—
Note 1. AVCC0/AVCC1/AVCC2/VREFH0/VREFH1/VREFH2 and VCC can be set individually within the operating range.
Note 2. When powering on the VCC and AVCC0/AVCC1/AVCC2/VREFH0/VREFH1/VREFH2 pins, power them on at the same time or
the VCC pin first and then the AVCC0/AVCC1/AVCC2/VREFH0/VREFH1/VREFH2 pin.
R01DS0278EJ0100 Rev.1.00
Mar 31, 2017
Page 69 of 131