PIC18F2682 Datasheet, PDF (427/484 Pages) Microchip Technology – 28/40/44-Pin Enhanced Flash Microcontrollers with ECAN Technology, 10-Bit A/D and nanoWatt Technology

PIC18F2682/2685/4682/4685
27.2 DC Characteristics: Power-Down and Supply Current
PIC18F2682/2685/4682/4685 (Industrial)
PIC18LF2682/2685/4682/4685 (Industrial) (Continued)
PIC18LF2682/2685/4682/4685
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC18F2682/2685/4682/4685
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
Device
Typ Max Units
Conditions
Supply Current (IDD)^(2,3)
PIC18LF268X/468X 65 220 μA
-40°C
65 220 μA
+25°C
VDD = 2.0V
70 220 μA
+85°C
PIC18LF268X/468X 120 330 μA
120 330 μA
130 330 μA
All devices 300 600 μA
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
240 600 μA
300 600 μA
+25°C
+85°C
VDD = 5.0V
Extended devices only 320 600 μA
+125°C
PIC18LF268X/468X 260 760 μA
-40°C
255 760 μA
+25°C
VDD = 2.0V
270 760 μA
PIC18LF268X/468X 420 1.4 μA
430 1.4 μA
450 1.4 μA
All devices 0.9 2.2 mA
+85°C
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 4 MHz
(PRI_IDLE mode,
EC oscillator)
0.9 2.2 mA
0.9 2.2 mA
+25°C
+85°C
VDD = 5.0V
Extended devices only 1
3
mA
+125°C
Extended devices only 2.8
7
mA
4.3 11 mA
+125°C
+125°C
VDD = 4.2V
VDD = 5.0V
FOSC = 25 MHz
(PRI_IDLE mode, EC oscillator)
All devices 6
18 mA
-40°C
6.2 18 mA
6.6 18 mA
All devices 8.1 22 mA
9.1 22 mA
+25°C
+85°C
-40°C
+25°C
VDD = 4.2 V
VDD = 5.0V
FOSC = 40 MHz
(PRI_IDLE mode,
EC oscillator)
8.3 22 mA
+85°C
Legend:
Note 1:
2:
3:
4:
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
© 2007 Microchip Technology Inc.
Preliminary
DS39761B-page 425