PIC16LF1824T39A_12 Datasheet, PDF (355/418 Pages) Microchip Technology – 20-Pin Flash Microcontrollers with XLP Technology

PIC16LF1824T39A
31.4
DC Characteristics: PIC16LF1824T39A-I
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
Param
No.
Sym.
VIL
D030
D030A
D031
D032
D033
VIH
D040
D040A
D041
D042
D043A
D043B
IIL
D060
Characteristic
Min.
Input Low Voltage
I/O PORT:
with TTL buffer
—
with Schmitt Trigger buffer
—
with I²C™ levels
—
with SMBus levels
—
MCLR, OSC1 (RC mode)
—
OSC1 (HS mode)
—
Input High Voltage
I/O PORT:
with TTL buffer
0.25 VDD +
0.8
with Schmitt Trigger buffer
with I²C™ levels
0.8 VDD
0.7 VDD
with SMBus levels
2.1
MCLR
0.8 VDD
OSC1 (HS mode)
0.7 VDD
OSC1 (RC mode)
0.9 VDD
Input Leakage Current (NOTE 2)
I/O ports
—
Typ†
—
—
—
—
—
—
—
—
—
—
—
—
—
±5
D061
D070*
D080
IPUR
VOL
VOH
D090
MCLR (NOTE 3)
—
Weak Pull-up Current
25
Output Low Voltage (NOTE 4)
I/O ports
—
Output High Voltage (NOTE 4)
I/O ports
VDD - 0.7
± 50
100
—
—
Capacitive Loading Specs on Output Pins
D101* COSC2 OSC2 pin
—
—
D101A* CIO
All Microcontroller I/O pins
—
—
Max. Units
Conditions
0.15 VDD V 1.8V  VDD  3.6V
0.2 VDD V 2.0V  VDD  3.6V
0.3 VDD V
0.8
V 2.7V  VDD  3.6V
0.2 VDD V (Note 1)
0.3 VDD V
—
V 1.8V  VDD  3.6V
—
V 2.0V  VDD  3.6V
—
V
—
V 2.7V  VDD  3.6V
—
V
—
V
—
V VDD > 2.0V (Note 1)
± 125
± 200
nA VSS  VPIN  VDD, Pin at high-
impedance at 85°C
nA VSS  VPIN  VDD at 85°C
200
VDD = 3.3V, VPIN = VSS
0.6
V
IOL = 6 mA, VDD = 3.3V
IOL = 1.8 mA, VDD = 1.8V
—
V
IOH = 3 mA, VDD = 3.3V
IOH = 1 mA, VDD = 1.8V
15
pF In XT, HS and LP modes when
external clock is used to drive
OSC1
50
pF
D101B* CIORF All RF I/O pins
—
—
25
pF
*
†
Note 1:
2:
3:
4:
These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external
clock in RC mode.
Negative current is defined as current sourced by the pin.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
Including OSC2 in CLKOUT mode.
 2012 Microchip Technology Inc.
Preliminary
DS41657A-page 355