PIC16LF1824T39A_12 Datasheet, PDF (353/418 Pages) Microchip Technology – 20-Pin Flash Microcontrollers with XLP Technology

PIC16LF1824T39A
31.2 DC Characteristics: PIC16LF1824T39A-I (Industrial)
PIC16LF1824T39A
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
Param
No.
Device
Characteristics
Min. Typ† Max. Units
VDD
Conditions
Note
Supply Current (IDD) (Note 1, 2)
D010
—
5.0
10
A
—
7.5
12
A
D011
—
88
110
A
—
133
190
A
D012
—
220
290
A
—
370
480
A
D013
—
55
160
A
—
90
230
A
Supply Current (IDD) (Note 1, 2)
D014
—
187
250
A
—
324
430
A
D015
D016
D017*
D018
D019
—
6
18
A
—
8
20
A
—
113
165
A
—
140
190
A
—
0.44 0.70
mA
—
0.70 _1.10
mA
—
0.70 1.20
mA
—
1.10 1.80
mA
—
2.10 _3.30
mA
—
3.20 3.60
mA
1.8 _{FOSC = 32 kHz}
3.0 ^{LP Oscillator mode, -40°C  TA  +85°C}
1.8 FOSC = 1 MHz
3.0 ^{XT Oscillator mode}
1.8 FOSC = 4 MHz
3.0 ^{XT Oscillator mode}
1.8 FOSC = 1 MHz
3.0 ^{EC Oscillator mode, Medium-Power mode}
1.8 FOSC = 4 MHz
3.0 ^{EC Oscillator mode,}
Medium-Power mode
1.8 FOSC = 31 kHz
3.0 ^{LFINTOSC mode, -40°C  TA  +85°C}
1.8 FOSC = 500 kHz
3.0 ^{MFINTOSC mode}
1.8 FOSC = 8 MHz
3.0 ^{HFINTOSC mode}
1.8 FOSC = 16 MHz
3.0 ^{HFINTOSC mode}
3.0 FOSC = 32 MHz
3.6 ^{HFINTOSC mode (Note 3)}
Supply Current (IDD) (Note 1, 2)
D020
—
2.50 3.30
mA
—
3.00 _3.60
mA
3.0 FOSC = 32 MHz
3.6 ^{HS Oscillator mode (Note 4)}
D021
—
210
350
A
—
362
680
A
1.8 FOSC = 4 MHz
3.0 ^{EXTRC mode (Note 5)}
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: 8 MHz internal oscillator with 4xPLL enabled.
4: 8 MHz crystal oscillator with 4xPLL enabled.
5: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in k.
 2012 Microchip Technology Inc.
Preliminary
DS41657A-page 353