AMIS-53050 Datasheet, PDF (9/107 Pages) AMI SEMICONDUCTOR – Frequency Agile Transceiver

AMIS-53050 Frequency Agile Transceiver
Data Sheet
2.2.1.2. Outputs
Table 4: Pin Output Parameters
Pin
Vol
(1)
Voh
(2)
Min. Max.
Min.
Max.
(V)
(V)
(V)
(V)
Iol
(1,3)
Min. Max.
mA
mA
Ioh
(2,3)
Min. Max.
mA
mA
AO
DO 0
0.4
Vdd-.4
2
-2
Notes:
1.
2.
3.
Vol, Iol are tested at Vdd = VDDmin volts unless otherwise stated
Voh, Ioh are tested at Vdd = VDDmin volts unless otherwise stated
Polarity on currents indicates direction of current: (+) for sinking and (-) for sourcing
Notes
Analog outputs
CMOS
2.2.1.3. I/O Pins
Table 5: I/O Pin Parameters
Pin
Vil
V
Min.
Vil
V
Max.
Vih
V
Min.
Vih
V
Max.
Vol
V
(1)
Vol
V
Max.
(1)
Voh
V
Min.
(2)
Voh
V
(2)
Iol
mA
Min.
(1)
Ioh
mA
Min.
(2)
Iozl
uA
Max.
(3)
Iozh
uA
Max.
(3)
Notes
AIO
DIO
0
0.3 0.8
1
0
0.4
Vdd-.4
Vdd
2
-2
1
-1
Schmitt
Notes:
1.
2.
3.
Vol, Iol are tested at Vdd = 3.1V.
Voh, Ioh are tested at Vdd = 3.1V.
Ioz is tested with Vdd = 3.5V.
*** Leakage on I/O pins is typically checked for +/- 10 microamps with the output device turned off and no pull-up or pull-down device present.
2.3 Operational Specifications
Table 6: Operational Specifications
Parameter
Min. Typ.
Receiver
Frequency range
Sensitivity
Noise figure
IIP2
IIP3
Image rejection
Input impedance
RSSI gain
I_IN
I_DDS Crystal mode
T_on
T_{RX_TX}/ T_{TX_RX}
IF bandwidth
LNA
Input trim
300
-107
-104
6.0
30
16
10
12
7.8
+60
+5
40
Figure 8
18
12
14
2
150
1500
300
1.2
Output trim
0.32
Max
.
960
-114
-111
9.0
50
20
14
16
4
0.91
2
Units
MHz
dBm
dBm
dB
dBm
dBm
dB
Ω
mV/dB
mA
mA
mA
us
us
kHz
pF
pF
Comment
Frequency is set by external VCO components & registers
@ 10kHz data rate (FSK/GFSK modulation)
@ 10kHz data rate (OOK modulation)
Dual tone test using RSSI
Dual tone test using RSSI
Modulated desired, single tone interferer
Receiver input impedance with given LNA input/output coils
Receiver current consumption at 900MHz (AMIS-53050-001)
Receiver current consumption at 900MHz (AMIS-53050-002)
Stand-by mode with crystal oscillator running
Stand-by to receive mode transition time
Transition time from RX to TX or TX to RX
The receiver bandwidth is fixed
Internal capacitor range for the receiver input
Internal capacitor range for the output of the LNA in the receiver
AMI Semiconductor – Jan. 07, M-20639-002
9
www.amis.com