RX63N_15 Datasheet, PDF (135/210 Pages) Renesas Technology Corp – Renesas MCUs

RX63N Group, RX631 Group
5. Electrical Characteristics
Table 5.5 DC Characteristics (4) (for G Version (+85 < Ta ≤ +105°C))
Conditions: VCC = AVCC0 = VREFH = VCC_USB = V_BATT = 2.7 to 3.6 V, VREFH0 = 2.7 V to AVCC0,
VSS = AVSS0 = VREFL/VREFL0 = VSS_USB = 0 V, T_a = T_opr
Item
Symbol Min. Typ. Max. Unit Test Conditions
Supply
current*¹
Max.*²
Normal Peripheral function: clock signal
*⁴
supplied*⁴
Peripheral function: clock signal
stopped*⁴
I_CC*³
— — 115 mA ICLK = 100 MHz
— 52 —
PCLKA = 100MHz
PCLKB = 50 MHz
FCLK = 50 MHz
— 40 —
BCLK = 100MHz
Sleep mode
— 25 80
All-module-clock-stop mode (reference value)
— 20 53
Increased by BGO operation*⁵
— 15 —
Low-speed operating mode 1*⁶
—4
—
ICLK = 1 MHz
Low-speed operating mode 2
—1
—
ICLK = 32.768 kHz
Software standby mode
— 0.2 9
Power supplied to RAM and USB resume
detecting unit
— 22 200 µA
Power not
supplied to RAM
and USB resume
detecting unit
Power-on reset circuit
and low-power
consumption function
disabled
— 21 60
Power-on reset circuit
and low-power
consumption function
enabled
— 6.2 28
Increase when the RTC
is operating
When a crystal oscillator
for low clock loads is in
use
— 1.0 —
When a crystal oscillator
for standard clock loads
is in use
— 3.0 —
RTC operating while
VCC is off (with the
battery backup function,
only the RTC and sub-
clock oscillator operate)
When a crystal oscillator
for low clock loads is in
use
When a crystal oscillator
for standard clock loads
is in use
— 0.9 —
— 1.6 —
— 1.7 —
V_BATT = 2.0 V, VCC = 0V
V_BATT = 3.3 V, VCC = 0V
V_BATT = 2.0 V(for
products with 100 pins or
more), VBATT = 2.3 V
(for the 64-pin product),
VCC = 0V
Analog
power
supply
current*⁷
—
During 12-bit A/D conversion (including temperature I_AVCC0 —
sensor)
During 10-bit A/D conversion
During D/A conversion (per unit)
I_VREFH*⁹ —
—
3.3 —
2.3 3.2
V_BATT = 3.3 V, VCC = 0V
mA
1.0 1.65 mA
0.7 1.0 mA
Waiting for A/D, D/A conversion (all units)*¹⁰
—
— 25 35
µA
A/D, D/A converter in standby mode (all units)*¹⁰
— 0.1 5
µA
Reference
power
supply
current
During 12-bit A/D conversion
Waiting for 12-bit A/D conversion (per unit)
12-bit A/D converter in standby mode (per unit)
I_VREFH0 —
0.6 0.7
mA
— 0.5 0.6 mA
— 0.1 2.0 µA
RAM standby voltage
VCC rising gradient
V_RAM
2.7 —
SrVCC 8.4 —
—
V
20000 µs/V
VCC falling gradient*⁸
SfVCC 8.4 — —
µs/V
R01DS0098EJ0180 Rev.1.80
May 13, 2014
Page 135 of 208