1GB-DDR3L-AS4C64M16D3L Datasheet, PDF (17/90 Pages) Alliance Semiconductor Corporation – JEDEC Standard Compliant

1Gb DDR3L – AS4C64M16D3L
- DLL Enable/Disable
The DLL must be enabled for normal operation. DLL enable is required during power up initialization, and upon
returning to normal operation after having the DLL disabled. During normal operation (DLL-on) with MR1 (A0=0),
the DLL is automatically disabled when entering Self-Refresh operation and is automatically re-enable upon exit
of Self-Refresh operation. Any time the DLL is enabled and subsequently reset, tDLLK clock cycles must occur
before a Read or synchronous ODT command can be issued to allow time for the internal clock to be
synchronized with the external clock. Failing to wait for synchronization to occur may result in a violation of the
tDQSCK, tAON, or tAOF parameters. During tDLLK, CKE must continuously be registered high. DDR3L SDRAM
does not require DLL for any Write operation, expect when RTT_WR is enabled and the DLL is required for
proper ODT operation. For more detailed information on DLL Disable operation are described in DLL-off Mode.
The direct ODT feature is not supported during DLL-off mode. The on-die termination resistors must be disabled
by continuously registering the ODT pin low and/or by programming the RTT_Nom bits MR1{A9,A6,A2} to {0,0,0}
via a mode register set command during DLL-off mode.
The dynamic ODT feature is not supported at DLL-off mode. User must use MRS command to set Rtt_WR,
MR2 {A10, A9} = {0, 0}, to disable Dynamic ODT externally
- Output Driver Impedance Control
The output driver impedance of the DDR3L SDRAM device is selected by MR1 (bit A1 and A5) as shown in MR1
definition figure.
- ODT Rtt Values
DDR3L SDRAM is capable of providing two different termination values (Rtt_Nom and Rtt_WR). The nominal
termination value Rtt_Nom is programmable in MR1. A separate value (Rtt_WR) may be programmable in MR2
to enable a unique Rtt value when ODT is enabled during writes. The Rtt_WR value can be applied during writes
even when Rtt_Nom is disabled.
- Additive Latency (AL)
Additive Latency (AL) operation is supported to make command and data bus efficient for sustainable bandwidth
in DDR3L SDRAM. In this operation, the DDR3L SDRAM allows a read or write command (either with or without
auto-precharge) to be issued immediately after the active command. The command is held for the time of the
Additive Latency (AL) before it is issued inside the device. The Read Latency (RL) is controlled by the sum of the
AL and CAS Latency (CL) register settings. Write Latency (WL) is controlled by the sum of the AL and CAS
Write Latency (CWL) register settings. A summary of the AL register options are shown in MR.
- Write leveling
For better signal integrity, DDR3L memory module adopted fly-by topology for the commands, addresses,
control signals, and clocks. The fly-by topology has benefits from reducing number of stubs and their length but
in other aspect, causes flight time skew between clock and strobe at every DRAM on DIMM. It makes difficult for
the Controller to maintain tDQSS, tDSS, and tDSH specification. Therefore, the controller should support ‘write
leveling’ in DDR3L SDRAM to compensate for skew.
- Output Disable
The DDR3L SDRAM outputs maybe enable/disabled by MR1 (bit 12) as shown in MR1 definition. When this
feature is enabled (A12=1) all output pins (DQs, DQS, DQS#, etc.) are disconnected from the device removing
any loading of the output drivers. This feature may be useful when measuring modules power for example. For
normal operation A12 should be set to ‘0’.
Confidential
17
Rev. 2.0
Aug. /2014