LM3S1G21 Datasheet, PDF (441/955 Pages) Texas Instruments – Stellaris® LM3S1G21 Microcontroller

Stellaris^® LM3S1G21 Microcontroller
Register 22: GPIO Port Control (GPIOPCTL), offset 0x52C
The GPIOPCTL register is used in conjunction with the GPIOAFSEL register and selects the specific
peripheral signal for each GPIO pin when using the alternate function mode. Most bits in the
GPIOAFSEL register are cleared on reset, therefore most GPIO pins are configured as GPIOs by
default. When a bit is set in the GPIOAFSEL register, the corresponding GPIO signal is controlled
by an associated peripheral. The GPIOPCTL register selects one out of a set of peripheral functions
for each GPIO, providing additional flexibility in signal definition. For information on the defined
encodings for the bit fields in this register, refer to Table 19-5 on page 859. The reset value for this
register is 0x0000.0000 for GPIO ports that are not listed in the table below.
Note: If the same signal is assigned to two different GPIO port pins, the signal is assigned to the
port with the lowest letter and the assignment to the higher letter port is ignored.
Important: All GPIO pins are configured as GPIOs and tri-stated by default (GPIOAFSEL=0,
GPIODEN=0, GPIOPDR=0, GPIOPUR=0, and GPIOPCTL=0, with the exception of the
pins shown in the table below. A Power-On-Reset (POR) or asserting RST puts the pins
back to their default state.
Table 9-12. GPIO Pins With Non-Zero Reset Values
GPIO Pins
PA[1:0]
PA[5:2]
PB[3:2]
PC[3:0]
Default State
UART0
SSI0
I²C0
JTAG/SWD
GPIOAFSEL GPIODEN GPIOPDR GPIOPUR
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
GPIOPCTL
0x1
0x2
0x3
0x1
GPIO Port Control (GPIOPCTL)
GPIO Port A (APB) base: 0x4000.4000
GPIO Port A (AHB) base: 0x4005.8000
GPIO Port B (APB) base: 0x4000.5000
GPIO Port B (AHB) base: 0x4005.9000
GPIO Port C (APB) base: 0x4000.6000
GPIO Port C (AHB) base: 0x4005.A000
GPIO Port D (APB) base: 0x4000.7000
GPIO Port D (AHB) base: 0x4005.B000
GPIO Port E (APB) base: 0x4002.4000
GPIO Port E (AHB) base: 0x4005.C000
GPIO Port F (APB) base: 0x4002.5000
GPIO Port F (AHB) base: 0x4005.D000
GPIO Port G (APB) base: 0x4002.6000
GPIO Port G (AHB) base: 0x4005.E000
GPIO Port H (APB) base: 0x4002.7000
GPIO Port H (AHB) base: 0x4005.F000
GPIO Port J (APB) base: 0x4003.D000
GPIO Port J (AHB) base: 0x4006.0000
Offset 0x52C
Type R/W, reset -
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
PMC7
PMC6
PMC5
PMC4
Type R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
PMC3
PMC2
PMC1
PMC0
Type R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
January 22, 2012
441
Texas Instruments-Production Data