M1A3P250-VQ100 Datasheet, PDF (63/210 Pages) Microsemi Corporation – ProASIC3 Flash Family FPGAs with Optional Soft ARM Support

ProASIC3 Flash Family FPGAs
Table 2-75 • 1.8 V LVCMOS Low Slew
Commercial-Case Conditions: T_J = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 3.0 V
Applicable to Standard I/O Banks
Drive
Strength
2 mA
Speed
Grade
Std.
t_DOUT
0.66
t_DP
15.01
t_DIN
0.04
t_PY
1.20
t_EOUT
0.43
t_ZL
13.15
t_ZH
15.01
t_LZ
1.99
t_HZ
1.99
Units
ns
–1
0.56 12.77 0.04 1.02 0.36 11.19 12.77 1.70 1.70 ns
–2
0.49 11.21 0.03 0.90 0.32 9.82 11.21 1.49 1.49 ns
4 mA
Std.
0.66 10.10 0.04 1.20 0.43 9.55 10.10 2.41 2.37 ns
–1
0.56 8.59 0.04 1.02 0.36 8.13 8.59 2.05 2.02 ns
–2
0.49 7.54 0.03 0.90 0.32 7.13 7.54 1.80 1.77 ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
1.5 V LVCMOS (JESD8-11)
Low-Voltage CMOS for 1.5 V is an extension of the LVCMOS standard (JESD8-5) used for general-
purpose 1.5 V applications. It uses a 1.5 V input buffer and a push-pull output buffer.
Table 2-76 • Minimum and Maximum DC Input and Output Levels
Applicable to Advanced I/O Banks
1.5 V
LVCMOS
VIL
VIH
VOL
VOH IOL IOH IOSL IOSH IIL¹ IIH²
Drive
Min.
Strength V
Max.
V
Min.
V
Max.,
V
Max.
V
Min.
V
Max. Max.
mA mA mA³ mA³ µA⁴ µA⁴
2 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 2 2 16 13 10 10
4 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 4 4 33 25 10 10
6 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 6 6 39 32 10 10
8 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 8 8 55 66 10 10
12 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 12 12 55 66 10 10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
Revision 15
2- 58