M1A3P250-VQ100 Datasheet, PDF (43/210 Pages) Microsemi Corporation – ProASIC3 Flash Family FPGAs with Optional Soft ARM Support

ProASIC3 Flash Family FPGAs
3.3 V LVCMOS Wide Range
Table 2-47 • Minimum and Maximum DC Input and Output Levels
Applicable to Advanced I/O Banks
3.3 V
Equiv.
LVCMOS Software
Wide Range Default
Drive
Drive
Strength
Strength
Option¹
VIL
Min. Max.
V
V
VIH
Min. Max.
V
V
VOL
Max.
V
VOH IOL IOH IOSL
Min.
V
Max.
µA µA mA⁴
IOSH IIL² IIH³
Max.
mA⁴ µA⁵ µA⁵
100 µA
2 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25
27 10 10
100 µA
4 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25
27 10 10
100 µA
6 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51
54 10 10
100 µA
8 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51
54 10 10
100 µA
12 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 103
109 10 10
100 µA
16 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 132
127 10 10
100 µA
24 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 268
181 10 10
Notes:
1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive
strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models.
2. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
3. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
4. Currents are measured at 85°C junction temperature.
5. All LVMCOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD8-B specification.
6. Software default selection highlighted in gray.
Table 2-48 • Minimum and Maximum DC Input and Output Levels
Applicable to Standard Plus I/O Banks
3.3 V LVCMOS
Wide Range
Drive Strength
Equiv.
Software
Default
Drive
Strength
Option¹
VIL
VIH
VOL
Min. Max. Min. Max. Max.
V
VVV
V
VOH
Min.
V
IOL IOH IOSL IOSH IIL² IIH³
Max. Max.
µA µA mA⁴ mA⁴ µA⁵ µA⁵
100 µA
2 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25
27 10 10
100 µA
4 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25
27 10 10
100 µA
6 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51
54 10 10
100 µA
8 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51
54 10 10
100 µA
12 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 103 109 10 10
100 μA
16 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 103 109 10 10
Notes:
1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive
strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models.
2. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
3. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
4. Currents are measured at 85°C junction temperature.
5. All LVMCOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD8-B specification.
6. Software default selection highlighted in gray.
Revision 15
2- 38