M1A3P250-VQ100 Datasheet, PDF (51/210 Pages) Microsemi Corporation – ProASIC3 Flash Family FPGAs with Optional Soft ARM Support

ProASIC3 Flash Family FPGAs
2.5 V LVCMOS
Low-Voltage CMOS for 2.5 V is an extension of the LVCMOS standard (JESD8-5) used for general-
purpose 2.5 V applications.
Table 2-56 • Minimum and Maximum DC Input and Output Levels
Applicable to Advanced I/O Banks
2.5 V LVCMOS
VIL
VIH
VOL VOH IOL IOH
IOSL
IOSH IIL1 IIH²
Min.
Drive Strength V
Max.
V
Min.
V
Max.
V
Max.
V
Min.
V mA mA
Max.
mA³
Max.
mA³
µA⁴ µA⁴
2 mA
–0.3
0.7
1.7
2.7
0.7
1.7 2 2
18
16
10 10
4 mA
–0.3 0.7
1.7
2.7
0.7
1.7 4 4
18
16
10 10
6 mA
–0.3 0.7
1.7
2.7
0.7
1.7 6 6
37
32
10 10
8 mA
–0.3 0.7
1.7
2.7
0.7
1.7 8 8
37
32
10 10
12 mA
–0.3 0.7
1.7
2.7
0.7
1.7 12 12
74
65
10 10
16 mA
–0.3 0.7
1.7
2.7
0.7
1.7 16 16
87
83
10 10
24 mA
–0.3 0.7
1.7
2.7
0.7
1.7 24 24
124
169
10 10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
Table 2-57 • Minimum and Maximum DC Input and Output Levels
Applicable to Standard Plus I/O Banks
2.5 V LVCMOS
VIL
VIH
VOL VOH IOL IOH
IOSL
IOSH IIL¹ IIH²
Min.
Drive Strength V
Max. Min. Max. Max. Min.
V
V
V
V
V mA mA
Max.
mA³
Max.
mA³
µA⁴ µA⁴
2 mA
–0.3
0.7
1.7 2.7
0.7 1.7 2 2
18
16
10 10
4 mA
–0.3
0.7
1.7 2.7
0.7 1.7 4 4
18
16
10 10
6 mA
–0.3
0.7
1.7 2.7
0.7 1.7 6 6
37
32
10 10
8 mA
–0.3
0.7
1.7 2.7
0.7 1.7 8 8
37
32
10 10
12 mA
–0.3
0.7
1.7 2.7
0.7 1.7 12 12
74
65
10 10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is
larger when operating outside recommended ranges
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
Revision 15
2- 46