PIC18F1XK22 Datasheet, PDF (339/388 Pages) Microchip Technology – 20-Pin Flash Microcontrollers with nanoWatt XLP Technology

PIC18F1XK22/LF1XK22
25.4 DC Characteristics: Primary Run Supply Current, PIC18F1XK22/LF1XK22-I/E
(Industrial, Extended)
PIC18LF1XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
PIC18F1XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device Characteristics
Typ. Max. Units
Conditions
D014
Supply Current (IDD)^{(1, 2, 4, 5)} .15 .28 mA -40°C to +125°C VDD = 1.8V
D014A
.22 .30 mA -40°C to +125°C VDD = 3.0V
FOSC = 1 MHz
(PRI_RUN,
EC Med Osc)
D014
D014A
D014B
.20 .32 mA -40°C to +125°C VDD = 1.8V
.27 .39 mA -40°C to +125°C VDD = 3.0V
.30 .42 mA -40°C to +125°C VDD = 5.0V
FOSC = 1 MHz
(PRI_RUN,
EC Med Osc)
D015
D015A
2.2 2.4 mA -40°C to +125°C VDD = 1.8V
3.5 4.0 mA -40°C to +125°C VDD = 3.0V
FOSC = 16 MHz
(PRI_RUN,
EC High Osc)
D015
D015A
D015B
2.4 2.6 mA -40°C to +125°C VDD = 1.8V
3.7 4.2 mA -40°C to +125°C VDD = 3.0V
3.9 4.4 mA -40°C to +125°C VDD = 5.0V
FOSC = 16 MHz
(PRI_RUN,
EC High Osc)
D016
11.5 14.0 mA -40°C to +125°C VDD = 3.0V
FOSC = 64 MHz
(PRI_RUN,
EC High Osc)
D016
D016A
11.9 14.4 mA -40°C to +125°C
12.1 14.6 mA -40°C to +125°C
VDD = 3.0V
VDD = 5.0V
FOSC = 64 MHz
(PRI_RUN,
EC High Osc)
D017
D017A
2.0 2.6 mA -40°C to +125°C VDD = 1.8V
FOSC = 4 MHz
16 MHz Internal
3.5 4.5 mA -40°C to +125°C VDD = 3.0V _{(PRI_RUN HS+PLL)}
D017
D017A
D017B
2.2 2.8 mA -40°C to +125°C VDD = 1.8V
FOSC = 4 MHz
3.7 4.7 mA -40°C to +125°C VDD = 3.0V
16 MHz Internal
3.8 4.8 mA -40°C to +125°C VDD = 5.0V ^{(PRI_RUN HS+PLL)}
D018
FOSC = 16 MHz
12 15 mA -40°C to +125°C VDD = 3.0V
64 MHz Internal
(PRI_RUN HS+PLL)
D018
D018A
12.4 15.4 mA -40°C to +125°C
12.6 15.6 mA -40°C to +125°C
VDD = 3.0V
VDD = 5.0V
FOSC = 16 MHz
64 MHz Internal
(PRI_RUN HS+PLL)
* These parameters are characterized but not tested.
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact
on the current consumption.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
extended by the formula IR = VDD/2REXT (mA) with REXT in k
4: FVR and BOR are disabled.
5: When a single temperature range is provided for a parameter, the specification applies to both industrial and extended
temperature devices.
 2010 Microchip Technology Inc.
Preliminary
DS41365D-page 339