English
Language : 

PIC18F1XK22 Datasheet, PDF (3/388 Pages) Microchip Technology – 20-Pin Flash Microcontrollers with nanoWatt XLP Technology
PIC18F1XK22/LF1XK22
20-Pin Flash Microcontrollers with nanoWatt XLP Technology
High-Performance RISC CPU:
• C Compiler Optimized Architecture:
- Optional extended instruction set designed to
optimize re-entrant code
• 256 bytes Data EEPROM
• Up to 16 Kbytes Linear Program Memory
Addressing
• Up to 512 bytes Linear Data Memory Addressing
• Up to 16 MIPS Operation
• 16-bit Wide Instructions, 8-bit Wide Data Path
• Priority Levels for Interrupts
• 31-Level, Software Accessible Hardware Stack
• 8 x 8 Single-Cycle Hardware Multiplier
Flexible Oscillator Structure:
• Precision 16 MHz Internal Oscillator Block:
- Factory calibrated to ± 1%
- Software selectable frequencies range of
31 kHz to 16 MHz
- 64 MHz performance available using PLL –
no external components required
• Four Crystal modes up to 64 MHz
• Two External Clock modes up to 64 MHz
• 4X Phase Lock Loop (PLL)
• Secondary Oscillator using Timer1 @ 32 kHz
• Fail-Safe Clock Monitor
- Allows for safe shutdown if peripheral clock
stops
• Two-Speed Oscillator Start-up
Special Microcontroller Features:
• Full 5.5V Operation – PIC18F1XK22
• 1.8V-3.6V Operation – PIC18LF1XK22
• Self-reprogrammable under Software Control
• Power-on Reset (POR), Power-up Timer (PWRT)
and Oscillator Start-up Timer (OST)
• Programmable Brown-out Reset (BOR)
• Extended Watchdog Timer (WDT):
- Programmable period from 4ms to 131s
• Programmable Code Protection
• In-Circuit Serial Programming™ (ICSP™) via
two pins
• In-Circuit Debug via Two Pins
Extreme Low-Power Management
PIC18LF1XK22 with nanoWatt XLP:
• Sleep mode: 34 nA
• Watchdog Timer: 460 nA
• Timer1 Oscillator: 650 nA @ 32 kHz
Analog Features:
• Analog-to-Digital Converter (ADC) module
- 10-bit resolution, 12 channels
- Auto acquisition capability
- Conversion available during Sleep
• Analog Comparator module:
- Two rail-to-rail analog comparators
- Independent input multiplexing
- Inputs and outputs externally accessible
• Voltage Reference module:
- Programmable (% of VDD), 16 steps
- Two 16-level voltage ranges using VREF pins
- Programmable Fixed Voltage Reference
(FVR), 3 levels
Peripheral Highlights:
• 17 I/O Pins and 1 Input-only Pin:
- High current sink/source 25 mA/25 mA
- Programmable weak pull-ups
- Programmable interrupt-on- change
- Three external interrupt pins
• Four Timer modules:
- 3 16-bit timers/counters with prescaler
- 1 8-bit timer/counter with 8-bit period register,
prescaler and postscaler
- Dedicated, low-power Timer1 oscillator
• Enhanced Capture/Compare/PWM (ECCP)
module:
- One, two or four PWM outputs
- Selectable polarity
- Programmable dead time
- Auto-shutdown and Auto-restart
- PWM output steering control
• Master Synchronous Serial Port (MSSP) module
- 3-wire SPI (supports all 4 SPI modes)
- I2C™ Master and Slave modes (Slave mode
address masking)
• Enhanced Universal Synchronous Asynchronous
Receiver Transmitter module (EUSART)
- Supports RS-232, RS-485 and LIN 2.0
- Auto-Baud Detect
- Auto Wake-up on Break
• SR Latch (555 Timer) module with:
- Configurable inputs and outputs
- Supports mTouch™ capacitive sensing
applications
 2010 Microchip Technology Inc.
Preliminary
DS41365D-page 3