MC9S08DZ60CLH Datasheet, PDF (380/416 Pages) Freescale Semiconductor, Inc – MC9S08DZ60 Series Features

Appendix A Electrical Characteristics
3 _{Monotonicity and No-Missing-Codes guaranteed in 10 bit and 8 bit modes}
4 _{Based on input pad leakage current. Refer to pad electricals.}
A.10 External Oscillator (XOSC) Characteristics
Table A-11. Oscillator Electrical Specifications (Temperature Range = –40 to 125°C Ambient)
Num C
Rating
Symbol
Min Typ¹ Max Unit
Oscillator crystal or resonator (EREFS = 1, ERCLKEN = 1
C
1
Low range (RANGE = 0)
High range (RANGE = 1) FEE or FBE mode ²
High range (RANGE = 1) PEE or PBE mode³
f_lo
f_hi-fll
f_hi-pll
32
— 38.4 kHz
1
—
5 MHz
1
—
16 MHz
High range (RANGE = 1, HGO = 1) BLPE mode
f_hi-hgo
1
—
16 MHz
High range (RANGE = 1, HGO = 0) BLPE mode
f_hi-lp
1
—
8 MHz
2 — Load capacitors
C₁
See crystal or resonator
C₂
manufacturer’s recommendation.
Feedback resistor
3—
Low range (32 kHz to 100 kHz)
R_F
—
10
— MΩ
High range (1 MHz to 16 MHz)
—
1
— MΩ
Series resistor
Low range, low gain (RANGE = 0, HGO = 0)
—
0
—
Low range, high gain (RANGE = 0, HGO = 1)
—
100 —
4—
High range, low gain (RANGE = 1, HGO = 0)
R_S
—
0
—
kΩ
High range, high gain (RANGE = 1, HGO = 1)
≥ 8 MHz
—
0
0
4 MHz
—
0
10
1 MHz
—
0
20
Crystal start-up time ⁴
Low range, low gain (RANGE = 0, HGO = 0)
t
CSTL-LP
—
200 —
5T
Low range, high gain (RANGE = 0, HGO = 1)
t
CSTL-HGO
—
400 —
High range, low gain (RANGE = 1, HGO = 0)⁵
t
CSTH-LP
—
5
—
ms
High range, high gain (RANGE = 1, HGO = 1)⁴
t
CSTH-HGO
—
15
—
Square wave input clock frequency (EREFS = 0, ERCLKEN = 1)
T
6
FEE or FBE mode ²
PEE or PBE mode³
f_extal
0.03125 —
1
—
5
16 MHz
BLPE mode
0
—
40
1 _{Typical data was characterized at 3.0 V, 25°C or is recommended value.}
2 _{When MCG is configured for FEE or FBE mode, the input clock source must be divisible using RDIV to within the range of}
31.25 kHz to 39.0625 kHz.
3 _{When MCG is configured for PEE or PBE mode, input clock source must be divisible using RDIV to within the range of 1 MHz}
to 2 MHz.
4 _{This parameter is characterized and not tested on each device. Proper PC board layout procedures must be followed to}
achieve specifications. This data will vary based upon the crystal manufacturer and board design. The crystal should be
characterized by the crystal manufacturer.
5 _{4 MHz crystal.}
MC9S08DZ60 Series Data Sheet, Rev. 4
380
Freescale Semiconductor