MSP430FR2033 Datasheet, PDF (1/89 Pages) Texas Instruments – Mixed-Signal Microcontrollers

Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
MSP430FR2033, MSP430FR2032
SLASE45B – OCTOBER 2014 – REVISED AUGUST 2015
MSP430FR203x Mixed-Signal Microcontrollers
1 Device Overview
1.1 Features
1
• Embedded Microcontroller
– 16-Bit RISC Architecture up to 16 MHz
– Wide Supply Voltage Range From 1.8 V to
3.6 V
• Optimized Low-Power Modes (at 3 V)
– Active: 126 µA/MHz
– Standby
• LPM3.5 With VLO: 0.4 µA
• Real-Time Clock (RTC) Counter (LPM3.5
With 32768-Hz Crystal): 0.77 µA
– Shutdown (LPM4.5): 15 nA
• Low-Power Ferroelectric RAM (FRAM)
– Up to 15.5KB of Nonvolatile Memory
– Built-In Error Correction Code (ECC)
– Configurable Write Protection
– Unified Memory of Program, Constants, and
Storage
– 10¹⁵ Write Cycle Endurance
– Radiation Resistant and Nonmagnetic
• Intelligent Digital Peripherals
– IR Modulation Logic
– Two 16-Bit Timers With Three Capture/Compare
Registers Each (Timer_A3)
– One 16-Bit Counter-Only RTC Counter
– 16-Bit Cyclic Redundancy Check (CRC)
• Enhanced Serial Communications
– Enhanced USCI A (eUSCI_A) Supports UART,
IrDA, and SPI
– Enhanced USCI B (eUSCI_B) Supports SPI and
I²C
• High-Performance Analog
– 10-Channel 10-Bit Analog-to-Digital Converter
(ADC)
• Internal 1.5-V Reference
• Sample-and-Hold 200 ksps
1.2 Applications
• Smoke or Fire Detectors
• Glass Breakage Detectors
• Industrial Sensor Management
• System Supervisor, Low-Power Coprocessors
• Clock System (CS)
– On-Chip 32-kHz RC Oscillator (REFO)
– On-Chip 16-MHz Digitally Controlled Oscillator
(DCO) With Frequency Locked Loop (FLL)
• ±1% Accuracy With On-Chip Reference at
Room Temperature
– On-Chip Very Low-Frequency 10-kHz Oscillator
(VLO)
– On-Chip High-Frequency Modulation Oscillator
(MODOSC)
– External 32-kHz Crystal Oscillator (XT1)
– Programmable MCLK Prescalar of 1 to 128
– SMCLK Derived From MCLK With
Programmable Prescalar of 1, 2, 4, or 8
• General Input/Output and Pin Functionality
– Total 60 I/Os on 64-Pin Package
– 16 Interrupt Pins (P1 and P2) Can Wake up
MCU From LPMs
– All I/Os are Capacitive Touch I/Os
• Development Tools and Software
– Free Professional Development Environments
• Family Members (Also See Section 3)
– MSP430FR2033: 15KB of Program FRAM +
512B of Information FRAM + 2KB of RAM
– MSP430FR2032: 8KB of Program FRAM +
512B of Information FRAM + 1KB of RAM
• Package Options
– 64 Pin: LQFP (PM)
– 56 Pin: TSSOP (G56)
– 48 Pin: TSSOP (G48)
• For Complete Module Descriptions, See the
MSP430FR4xx and MSP430FR2xx Family User's
Guide (SLAU445)
• Temperature Sensors or Controllers
• Data Storage, Data Integration
• Human Machine Interface (HMI) Controllers
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.