4583 Datasheet, PDF (99/153 Pages) Renesas Technology Corp – SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER

4583 Group
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
MACHINE INSTRUCTIONS (INDEX BY ALPHABET) (continued)
SNZT1 (Skip if Non Zero condition of Timer 1 interrupt request flag)
Instruction
code
D9
D0
Number of
1010000000
280
2
16
words
1
Number of
cycles
1
Flag CY
–
Skip condition
V12 = 0: (T1F) = 1
Operation:
V12 = 0: (T1F) = 1 ?
After skipping, (T1F) ← 0
V12 = 1: SNZT1 = NOP
(V12 = bit 2 of interrupt control register V1)
Grouping: Timer operation
Description: When V12 = 0 : Skips the next instruction
when timer 1 interrupt request flag T1F is
“1.” After skipping, clears (0) to the T1F
flag. When the T1F flag is “0,” executes the
next instruction.
When V12 = 1 : This instruction is equiva-
lent to the NOP instruction.
SNZT2 (Skip if Non Zero condition of Timer 2 interrupt request flag)
Instruction
code
D9
D0
Number of
1010000001
281
2
16
words
1
Number of
cycles
1
Flag CY
–
Skip condition
V13 = 0: (T2F) = 1
Operation:
V13 = 0: (T2F) = 1 ?
After skipping, (T2F) ← 0
V13 = 1: SNZT2 = NOP
(V13 = bit 3 of interrupt control register V1)
Grouping: Timer operation
Description: When V13 = 0 : Skips the next instruction
when timer 2 interrupt request flag T2F is
“1.” After skipping, clears (0) to the T2F
flag. When the T2F flag is “0,” executes the
next instruction.
When V13 = 1 : This instruction is equiva-
lent to the NOP instruction.
SNZT3 (Skip if Non Zero condition of Timer 3 interrupt request flag)
Instruction
code
D9
D0
Number of
1010000010
282
2
16
words
1
Number of
cycles
1
Flag CY
–
Skip condition
V20 = 0: (T3F) = 1
Operation:
V20 = 0: (T3F) = 1 ?
After skipping, (T3F) ← 0
V20 = 1: SNZT3 = NOP
(V20 = bit 0 of interrupt control register V2)
Grouping: Timer operation
Description: When V20 = 0 : Skips the next instruction
when timer 3 interrupt request flag T3F is
“1.” After skipping, clears (0) to the T3F
flag. When the T3F flag is “0,” executes the
next instruction.
When V20 = 1 : This instruction is equiva-
lent to the NOP instruction.
SNZT4 (Skip if Non Zero condition of Timer 4 inerrupt request flag)
Instruction
code
D9
D0
Number of
1
0
1
0
0
0
0
0
1
1
2
2
8
3 ₁₆
words
1
Number of
cycles
1
Flag CY
–
Skip condition
V21 = 0: (T4F) = 1
Operation:
V21 = 0: (T4F) = 1 ?
After skipping, (T4F) ← 0
V21 = 1: SNZT4 = NOP
(V21 = bit 1 of interrupt control register V2)
Grouping: Timer operation
Description: When V21 = 0 : Skips the next instruction
when timer 4 interrupt request flag T4F is
“1.” After skipping, clears (0) to the T4F
flag. When the T4F flag is “0,” executes the
next instruction.
When V21 = 1 : This instruction is equiva-
lent to the NOP instruction.
Rev.3.00 Aug 06, 2004 page 99 of 151
REJ03B0009-0300Z