M306H2MC-XXXFP Datasheet, PDF (19/210 Pages) Renesas Technology Corp – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER

MITSUBISHI MICROCOMPUTERS
M306H2MC-XXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
with DATA ACQUISITION CONTROLLER
Processor mode register 0 (Note)
(000416)···
0016
Processor mode register 1
(000516)··· 0 0 0 0 0
0
System clock control register 0
(000616)··· 0 1 0 0 1 0 0 0
System clock control register 1
(000716)··· 0 0 1 0 0 0 0 0
Chip select control register
(000816)··· 0 0 0 0 0 0 0 1
Address match interrupt enable register ^{(000916)···}
00
Protect register
(000A16)···
000
Watchdog timer control register
Address match interrupt register 0
Address match interrupt register 1
DMA0 control register
DMA1 control register
INT3 interrupt control register
Timer B5 interrupt control register
Timer B4 interrupt control register
Timer B3 interrupt control register
SI/O4 interrupt control register
(000F16)··· 0 0 0 ? ? ? ? ?
(001016)···
0016
(001116)···
0016
(001216)···
0000
(001416)···
0016
(001516)···
0016
(001616)···
0000
(002C16)··· 0 0 0 0 0 ? 0 0
(003C16)··· 0 0 0 0 0 ? 0 0
(004416)···
00?000
(004516)···
?000
(004616)···
?000
(004716)···
?000
(004816)···
00?000
SI/O3 interrupt control register
Bus collision detection interrupt
control register
DMA0 interrupt control register
(004916)···
(004A16)···
(004B16)···
DMA1 interrupt control register
(004C16)···
Key input interrupt control register
(004D16)···
A-D conversion interrupt control register (004E16)···
UART2 transmit interrupt control register (004F16)···
UART2 receive interrupt control register (005016)···
UART0 transmit interrupt control register _{(005116)···}
UART0 receive interrupt control register _{(005216)···}
UART1 transmit interrupt control register _{(005316)···}
UART1 receive interrupt control register _{(005416)···}
Timer A0 interrupt control register
(005516)···
Timer A1 interrupt control register
(005616)···
Timer A2 interrupt control register
(005716)···
Timer A3 interrupt control register
(005816)···
Timer A4 interrupt control register
(005916)···
00?000
?000
?000
?000
?000
?000
?000
?000
?000
?000
?000
?000
?000
?000
?000
?000
?000
Timer B0 interrupt control register
Timer B1 interrupt control register
Timer B2 interrupt control register
INT0 interrupt control register
INT1 interrupt control register
INT2 interrupt control register
Slice RAM address control register
Slice RAM data control register
(005A16)···
(005B16)···
(005C16)···
(005D16)···
(005E16)···
(005F16)···
(020E16)···
(020F16)···
(021016)···
(021116)···
?000
?000
?000
00?000
00?000
00?000
0016
0016
0016
0016
Address control register for expansion register (021616)···
0016
(021716)···
0016
Data control register for expansion register
(021816)···
0016
(021916)···
0016
Humming 8/4 register
(021A16)···
0016
(021B16)···
0016
Humming 24/18 register0
(021C16)···
0016
(021D16)···
0016
Humming 24/18 register1
Timer B3,4,5 count start flag
(021E16)···
0016
(021F16)···
0016
(034016)··· 0 0 0
Timer B3 mode register
Timer B4 mode register
Timer B5 mode register
Interrupt cause select register
SI/O3 control register
SI/O4 control register
(035B16)··· _{0 0 ? 0 0 0 0}
(035C16)··· 0 0 ? 0 0 0 0
(035D16)··· _{0 0 ? 0 0 0 0}
(035F16)···
0016
(036216)···
4016
(036616)···
4016
UART2 special mode register 2
UART2 special mode register
(037616)···
(037716)···
0016
0016
UART2 transmit/receive mode register
UART2 transmit/receive control register 0
UART2 transmit/receive control register 1
(037816)···
0016
(037C16)··· 0 0 0 0 1 0 0 0
(037D16)··· 0 0 0 0 0 0 1 0
x : Nothing is mapped to this bit
? : Undefined
The content of other registers and RAM is undefined when the microcomputer is reset. The initial values must therefore be set.
Note: When the VCC level is applied to the CNVSS pin, it is 0316 at a reset.
Figure 2.3.3 Device's internal status after a reset is cleared
18
Rev. 1.0