M306H2MC-XXXFP Datasheet, PDF (135/210 Pages) Renesas Technology Corp – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER

MITSUBISHI MICROCOMPUTERS
M306H2MC-XXXFP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
with DATA ACQUISITION CONTROLLER
A-D control register 0 (Note 1)
b7 b6 b5 b4 b3 b2 b1 b0
Symbol
ADCON0
Address
03D616
When reset
00000XXX2
Bit symbol
Bit name
Function
RW
CH0
CH1
CH2
MD0
MD1
Analog input pin select bit
A-D operation mode
select bit 0
b2 b1 b0
0 0 0 : AN0 is selected
0 0 1 : AN1 is selected
0 1 0 : AN2 is selected
0 1 1 : AN3 is selected
1 0 0 : AN4 is selected
1 0 1 : AN5 is selected
1 1 0 : AN6 is selected
1 1 1 : AN7 is selected
b4 b3
0 0 : One-shot mode
0 1 : Repeat mode
1 0 : Single sweep mode
1 1 : Repeat sweep mode 0
Repeat sweep mode 1
(Note 2)
(Note 2)
TRG
Trigger select bit
0 : Software trigger
1 : ADTRG trigger
ADST
A-D conversion start flag 0 : A-D conversion disabled
1 : A-D conversion started
CKS0
Frequency select bit 0
0 : fAD/4 is selected
1 : fAD/2 is selected
Note 1: If the A-D control register is rewritten during A-D conversion, the conversion result is
indeterminate.
Note 2: When changing A-D operation mode, set analog input pin again.
A-D control register 1 (Note)
b7 b6 b5 b4 b3 b2 b1 b0
0
Symbol
ADCON1
Address
03D716
When reset
0016
Bit symbol
Bit name
A-D sweep pin select bit
SCAN0
SCAN1
MD2
A-D operation mode
select bit 1
Function
When single sweep and repeat sweep
mode 0 are selected
b1 b0
0 0 : AN0, AN1 (2 pins)
0 1 : AN0 to AN3 (4 pins)
1 0 : AN0 to AN5 (6 pins)
1 1 : AN0 to AN7 (8 pins)
When repeat sweep mode 1 is selected
b1 b0
0 0 : AN0 (1 pin)
0 1 : AN0, AN1 (2 pins)
1 0 : AN0 to AN2 (3 pins)
1 1 : AN0 to AN3 (4 pins)
0 : Any mode other than repeat sweep
mode 1
1 : Repeat sweep mode 1
RW
Reserved bit
Must always be set to "0"
CKS1 ^{Frequency select bit 1}
0 : fAD/2 or fAD/4 is selected
1 : fAD is selected
VCUT ^{Vref connect bit}
0 : Vref not connected
1 : Vref connected
OPA0
OPA1
External op-amp
connection mode bit
b7 b6
0 0 : ANEX0 and ANEX1 are not used
0 1 : ANEX0 input is A-D converted
1 0 : ANEX1 input is A-D converted
1 1 : External op-amp connection mode
Note: If the A-D control register is rewritten during A-D conversion, the conversion result is
indeterminate.
Figure 2.12.2 A-D converter-related registers (1)
134
Rev. 1.0