D20419-80 Datasheet, PDF (66/386 Pages) ITT Industries – Military/Aerospace

DPX ARINC 404
DPX
Modfication Codes
#4-40 CLINCH NUTS
Modfication
- 19**
Applicable Series
DPX2-33B
DPXB-33
DPX2-34B
DPXB-34
DPX3-33
DPX3-34 (Same as Code -01)
MODIFICATION 19
MODIFICATION 20
- 20
DPX2-33A
DPX2-34A
SUPERSEDED BY
01 MOD.
MODIFICATION 22
- 22
DPX2-33 and 34
DPX2-33A
DPX2-33B
DPXB-33
DPX2-33M and 34M
DPX3-33
DPXBME, DPX2ME, DPX3ME,
DPX4ME - 33 only
DPX2-33F and 34F
- 23
DPX2-33 and 34
.022 (0.56) MAX.
.037
(0.94)
.025 (0.64) MAX.
DPX2-33A
DPX2-33B
.014 (0.36) MAX.
4 PLACES
.255 (6.48)
DIA. MAX.
MAX.
.019
(0.48)
MIN
.037 MAX.
(0.94)
.255 (6.48)
DIA. MAX.
4 PLACES
.037
(0.94)
MAX.
.015
(0.38)
MIN
DPXB-33
DPX2-34B
DPXB-34
DPX3-33 and 34
DPX4-33 and 34
DPX2-33F and 34F
1
RIVET
4 REQD.
FRONT FACE OF
FLANGE
- 34 RECEPT.
- 33 PLUG
MODIFICATION 23
- 24
MOUNTING
HOLES(4), . 156(3.96)
DIA.
MODIFICATION 25
- 25
DPX2-34A
DPX2-33B
DPX2-34B
DPXB-34
1
- 26
MOUNTING
HOLES(4), . 120 (3.05)
DIA., C'SUNK 82 TO
.230 (5.84) DIA.
MODIFICATION 26
- 29
DPX2-34B
DPXB-34
DPX3-34
1
DPX2-34A
- 29
- 30
- 31
- 33
- 37
DPXBME-34P & 33S
DPX2ME-34P & 33S
DPX3ME-34P & 33S
1
DPX4ME-34P & 33S
DPXBME-34P
DPX2ME-34P
DPX3ME-34P
2
DPX4ME-34P
DPXBME-34P
DPX2ME-34P
DPX3ME-34P
DPX4ME-34P
2
DPXBME-34P
DPX2ME-34P
DPX3ME-34P
DPX4ME-34P
2
DPXBME-34P
DPX2ME-34P
DPX3ME-34P
DPX4ME-34P
2
1 Applicable for all MA, ME, NA and NE Series Connectors.
2
Definition
With six #4-40 clinch nuts in mounting holes.
Do not assign - use -01 code
Standard construction without tabs on insert retaining plate.
With eight #4-40 clinch nuts in mounting holes.
Same as 01. 01 Recommended
With floating eyelets.
With six mounting holes .208 (5.28) dia. (Foating eyelets omitted)
With four mounting holes .157 (3.99)/.155 (3.94) dia. (Clinch nuts omitted)
Mounting holes .120 (3.05) dia. countersunk 82* to .230 (5.84) dia.
and has tabs for attaching junction shells.
With interfacial seal (if pins) without junction shell tabs and military gold
plating on the contact.
Standard except less grommet*
* On the A106S layout the grommet is replaced by the separator.
Standard except less grommet and with tabs for
attaching junction shells.
(-34 pin only)
Standard except less grommet and with floating
bushings. (Slatted shells).
Standard except less grommet and with clinch
nuts in mounting holes.
Standard less grommet and with clinch nuts in mounting holes
and with tabs for attaching junction shells.
**Indicates polarizing position. (See page 68)
Dimensions are shown in inches (millimeters).
Dimensions subject to change.
www.ittcannon.com
66