DS681 Datasheet, PDF (40/56 Pages) Xilinx, Inc – Fast look-ahead carry logic

R
Table 36: Switching Characteristics for the DLL
Speed Grade
-4
Symbol
Description
Device Min Max Units
Output Frequency Ranges
CLKOUT_FREQ_CLK0
Frequency for the CLK0 and CLK180 outputs
All
5
250 MHz
CLKOUT_FREQ_CLK90
Frequency for the CLK90 and CLK270 outputs
5
200 MHz
CLKOUT_FREQ_2X
Frequency for the CLK2X and CLK2X180 outputs
10
334 MHz
CLKOUT_FREQ_DV
Output Clock Jitter^(2,3,4)
Frequency for the CLKDV output
0.3125 166 MHz
CLKOUT_PER_JITT_0
Period jitter at the CLK0 output
All
–
±100 ps
CLKOUT_PER_JITT_90
Period jitter at the CLK90 output
–
±150 ps
CLKOUT_PER_JITT_180
Period jitter at the CLK180 output
–
±150 ps
CLKOUT_PER_JITT_270
Period jitter at the CLK270 output
–
±150 ps
CLKOUT_PER_JITT_2X
Period jitter at the CLK2X and CLK2X180 outputs
±[0.5% ps
–
of CLKIN
period
+ 100]
CLKOUT_PER_JITT_DV1
Period jitter at the CLKDV output when performing integer division
–
±150 ps
CLKOUT_PER_JITT_DV2
Period jitter at the CLKDV output when performing non-integer division
Duty Cycle⁽⁴⁾
±[0.5% ps
–
of CLKIN
period
+ 100]
CLKOUT_DUTY_CYCLE_DLL Duty cycle variation for the CLK0, CLK90, CLK180, CLK270, CLK2X,
All
CLK2X180, and CLKDV outputs, including the BUFGMUX and clock tree
duty-cycle distortion
Phase Alignment⁽⁴⁾
±[1% of ps
–
CLKIN
period
+ 350]
CLKIN_CLKFB_PHASE
Phase offset between the CLKIN and CLKFB inputs
All
–
±150 ps
CLKOUT_PHASE_DLL
Phase offset between DLL outputs
CLK0 to CLK2X
(not CLK2X180)
±[1% of ps
–
CLKIN
period
+ 100]
All others
±[1% of ps
–
CLKIN
period
+ 150]
Lock Time
LOCK_DLL⁽³⁾
When using the DLL alone: The time
5 MHz < F_CLKIN < 15 MHz
All
–
from deassertion at the DCM’s Reset
5
ms
input to the rising transition at its
F_CLKIN > 15 MHz
600 μs
LOCKED output. When the DCM is
locked, the CLKIN and CLKFB signals
–
are in phase
Delay Lines
DCM_DELAY_STEP⁽⁵⁾
Finest delay resolution, averaged over all steps
All
15
35
ps
Notes:
1. The numbers in this table are based on the operating conditions set forth in Table 8 and Table 35.
2. Indicates the maximum amount of output jitter that the DCM adds to the jitter on the CLKIN input.
3. For optimal jitter tolerance and faster lock time, use the CLKIN_PERIOD attribute.
4. Some jitter and duty-cycle specifications include 1% of input clock period or 0.01 UI. For example, the data sheet specifies a maximum
jitter of “±[1% of CLKIN period + 150]”. Assume the CLKIN frequency is 100 MHz. The equivalent CLKIN period is 10 ns and 1% of 10 ns
is 0.1 ns or 100 ps. According to the data sheet, the maximum jitter is ±[100 ps + 150 ps] = ±250ps.
5. The typical delay step size is 23 ps.
40
www.xilinx.com
DS681 (v1.1) February 3, 2009
Product Specification