DS680 Datasheet, PDF (3/36 Pages) Xilinx, Inc – Space-Grade Virtex-4QV FPGAs

R
Space-Grade Virtex-4QV FPGAs: DC and Switching Characteristics
Table 4: Quiescent Supply Current
Symbol
Description
I_CCINTQ
Quiescent V_CCINT supply current
I_CCOQ
Quiescent V_CCO supply current
I_CCAUXQ
Quiescent V_CCAUX supply current
Device
XQR4VSX55
XQR4VFX60
XQR4VFX140
XQR4VLX200
XQR4VSX55
XQR4VFX60
XQR4VFX140
XQR4VLX200
XQR4VSX55
XQR4VFX60
XQR4VFX140
XQR4VLX200
Typ ⁽¹⁾
488
365
796
880
3.00
3.00
5.00
5.00
137
120
215
225
Max
Note (4)
Note (4)
Note (4)
Note (4)
Note (4)
Note (4)
Note (4)
Note (4)
Note (4)
Note (4)
Note (4)
Note (4)
Units
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
Notes:
1. Typical values are specified at nominal voltage, 25°C.
2. Typical values are for blank configured devices with no output current loads, no active input pull-up resistors, all I/O pins are 3-state and floating.
3. If DCI or differential signaling is used, more accurate quiescent current estimates can be obtained by using the Power Estimator or XPOWER tool.
4. Use the XPower™ Estimator (XPE) tool to calculate maximum static power for specific process, voltage, and temperature conditions.
Power-On Power Supply Requirements
Xilinx® FPGAs require a certain amount of supply current
during power-on to ensure proper device initialization. The
actual current consumed depends on the power-on ramp
rate of the power supply.
The power supplies can be turned on in any sequence,
though the specifications shown in Table 5 are for the
recommended power-on sequence of V_CCINT, V_CCAUX,
V_CCO. Xilinx does not specify the current for other power-on
sequences.
Table 5 shows the maximum current required by Virtex-4
devices for proper power-on and configuration.
Once initialized and configured, use the XPOWER tool to
estimate current drain on these supplies.
Table 5: Maximum Power-On Current for Virtex-4QV Devices
Device
I_CCINT
Typ ⁽¹⁾
Max⁽²⁾
I_CCAUX
Typ ⁽¹⁾
Max⁽²⁾
Typ ⁽¹⁾
I_CCO
Max⁽²⁾
Units
XQR4VSX55
520
5355
225
930
150
450
mA
XQR4VFX60
410
4680
220
1050
150
435
mA
XQR4VFX140
860
9540
450
1313
250
563
mA
XQR4VLX200
1020
8820
500
1313
250
600
mA
Notes:
1. Typical values are specified at nominal voltage, 25°C.
2. Maximum values are specified under worst-case process, voltage, and military temperature conditions.
Table 6: Power Supply Ramp Time
Symbol
Description
V_CCINT
V_CCO
V_CCAUX
Internal supply voltage relative to GND
Output drivers supply voltage relative to GND
Auxiliary supply voltage relative to GND
Ramp Time
0.20 to 50.0
0.20 to 50.0
0.20 to 50.0
Units
ms
ms
ms
DS680 (v2.0) April 12, 2010
www.xilinx.com
Product Specification
3