DS893 Datasheet, PDF (2/77 Pages) Xilinx, Inc – DC and AC Switching Characteristics

Virtex UltraScale FPGAs Data Sheet: DC and AC Switching Characteristics
Table 1: Absolute Maximum Ratings⁽¹⁾ (Cont’d)
Symbol
Description
Min
Max
Units
GTH or GTY Transceiver
V_MGTAVCC
Analog supply voltage for the GTH or GTY transmitter and
receiver circuits.
–0.500
1.100
V
V_MGTAVTT
Analog supply voltage for the GTH or GTY transmitter and
receiver termination circuits.
–0.500
1.320
V
V_MGTVCCAUX
Auxiliary analog Quad PLL (QPLL) voltage supply for the GTH or
GTY transceivers.
–0.500
1.935
V
V_MGTREFCLK
V_MGTAVTTRCAL
GTH or GTY transceiver reference clock absolute input voltage.
Analog supply voltage for the resistor calibration circuit of the
GTH or GTY transceiver column.
–0.500
–0.500
1.320
V
1.320
V
V_IN
Receiver (RXP/RXN) and Transmitter (TXP/TXN) absolute input
voltage.
–0.500
1.260
V
I_DCIN-FLOAT
DC input current for receiver input pins DC coupled RX
termination = floating.
–
10
mA
I_DCIN-MGTAVTT
I_DCIN-GND
DC input current for receiver input pins DC coupled RX
termination = V_MGTAVTT.
DC input current for receiver input pins DC coupled RX
termination = GND.
–
0⁽⁹⁾
mA
–
0⁽⁹⁾
mA
I_DCIN-PROG
DC input current for receiver input pins DC coupled RX
termination = Programmable.
–
0⁽⁹⁾
mA
I_DCOUT-FLOAT
DC output current for transmitter pins DC coupled RX
termination = floating.
–
10
mA
I_{DCOUT-MGTAVTT}
DC output current for transmitter pins DC coupled RX
termination = V_MGTAVTT.
System Monitor
–
6
mA
V_CCADC
System Monitor supply relative to GNDADC.
V_REFP
System Monitor reference input relative to GNDADC.
Temperature
–0.500
–0.500
2.000
V
2.000
V
T_STG
T_SOL
T_j
Storage temperature (ambient).
Maximum soldering temperature⁽¹⁰⁾.
Maximum junction temperature⁽¹⁰⁾.
–65
150
°C
–
260
°C
–
125
°C
Notes:
1. Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are
stress ratings only, and functional operation of the device at these or any other conditions beyond those listed under
Operating Conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time might
affect device reliability.
2. V_{CCINT_IO} must be connected to V_CCINT.
3. V_{CCAUX_IO} must be connected to V_CCAUX.
4. The lower absolute voltage specification always applies.
5. If V_CCO is 3.3V, the maximum voltage is 3.4V.
6. For I/O operation, see the UltraScale Architecture SelectIO Resources User Guide (UG571).
7. The maximum limit applied to DC signals. For maximum undershoot and overshoot AC specifications, see Table 4 and
Table 5.
8. See Table 12 for TMDS_33 specifications.
9. For more information on supported GTH or GTY transceiver terminations see the UltraScale Architecture GTH Transceiver
User Guide (UG576) or the UltraScale Architecture GTY Transceiver User Guide (UG578)
10. For soldering guidelines and thermal considerations, see the UltraScale and UltraScale+ FPGAs Packaging and Pinout
Specifications (UG575).
DS893 (v1.7.1) April 4, 2016
Product Specification
www.xilinx.com
Send Feedback
2