TLK110 Datasheet, PDF (76/104 Pages) Texas Instruments – Industrial Temp, Single Port 10/100Mbs Ethernet Physical Layer

TLK110
SLLS901A – DECEMBER 2011 – REVISED FEBRUARY 2012
www.ti.com
8.5.7 Cable Diagnostic Location Results Register 5 (CDLRR5)
This register provides the peaks locations after execution of the TDR. The values of this register are valid
after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-41. Cable Diagnostic Location Results Register 5 (CDLRR5), address 0x0184
BIT NAME
15:8 TPRD Peak
Location 5
7:0 TPRD Peak
Location 4
DEFAULT
<0000 0000>, RO
<0000 0000>, RO
FUNCTION
Location of the Fifth peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into distance from the PHY.
Location of the Fourth peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into distance from the PHY.
8.5.8 Cable Diagnostic Amplitude Results Register 1 (CDARR1)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-42. Cable Diagnostic Amplitude Results Register 1 (CDARR1), address 0x0185
BIT NAME
15 RESERVED
14:8 TPTD Peak
Amplitude 2
7 RESERVED
6:0 TPTD Peak
Amplitude 1
DEFAULT
0,RO
<000 0000>,RO
0,RO
<000 0000>,RO
FUNCTION
RESERVED: Writes ignored, read as 0.
Amplitude of the Second peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into type of cable fault and/or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR1 (0x180)
RESERVED: Writes ignored, read as 0.
Amplitude of the First peak discovered by the TDR mechanism on Transmit Channel (TPTD).
The value of these bits is translated into type of cable fault and/or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR1 (0x180)
8.5.9 Cable Diagnostic Amplitude Results Register 2 (CDARR2)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-43. Cable Diagnostic Amplitude Results Register 2 (CDARR2), address 0x0186
BIT NAME
15 RESERVED
14:8 TPTD Peak
Amplitude 4
7 RESERVED
6:0 TPTD Peak
Amplitude 3
DEFAULT
0,RO
<000 0000>,RO
0,RO
<000 0000>,RO
FUNCTION
RESERVED: Writes ignored, read as 0.
Amplitude of the Fourth peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into type of cable fault and/or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR2 (0x181)
RESERVED: Writes ignored, read as 0.
Amplitude of the Third peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into type of cable fault and/or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR2 (0x181)
8.5.10 Cable Diagnostic Amplitude Results Register 3 (CDARR3)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-44. Cable Diagnostic Amplitude Results Register 3 (CDARR3), address 0x0187
BIT NAME
15 RESERVED
14:8 TPRD Peak
Amplitude 1
DEFAULT
0,RO
<000 0000>,RO
FUNCTION
RESERVED: Writes ignored, read as 0.
Amplitude of the First peak discovered by the TDR mechanism on Receive Channel (TPRD).
The value of these bits is translated into type of cable fault and/or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR3 (0x182)
76
Register Block
Submit Documentation Feedback
Product Folder Link(s): TLK110
Copyright © 2011–2012, Texas Instruments Incorporated