LM3S6G11 Datasheet, PDF (401/827 Pages) Texas Instruments – Stellaris® LM3S6G11 Microcontroller

OBSOLETE: TI has discontinued production of this device.
Stellaris^® LM3S6G11 Microcontroller
Table 9-6. GPIO Pins With Non-Zero Reset Values
GPIO Pins
PA[1:0]
PA[5:2]
PB[3:2]
PC[3:0]
Default State
UART0
SSI0
I²C0
JTAG/SWD
GPIOAFSEL GPIODEN GPIOPDR GPIOPUR
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
GPIOPCTL
0x1
0x2
0x3
0x1
The default register type for the GPIOCR register is RO for all GPIO pins with the exception of the
NMI pin and the four JTAG/SWD pins (PB7 and PC[3:0]). These five pins are the only GPIOs that
are protected by the GPIOCR register. Because of this, the register type for GPIO Port B7 and GPIO
Port C[3:0] is R/W.
The default reset value for the GPIOCR register is 0x0000.00FF for all GPIO pins, with the exception
of the NMI pin and the four JTAG/SWD pins (PB7 and PC[3:0]). To ensure that the JTAG port is
not accidentally programmed as GPIO pins, the PC[3:0] pins default to non-committable. Similarly,
to ensure that the NMI pin is not accidentally programmed as a GPIO pin, the PB7 pin defaults to
non-committable. Because of this, the default reset value of GPIOCR for GPIO Port B is 0x0000.007F
while the default reset value of GPIOCR for Port C is 0x0000.00F0.
Table 9-7. GPIO Register Map
Offset Name
Type
0x000 GPIODATA
0x400 GPIODIR
0x404 GPIOIS
0x408 GPIOIBE
0x40C GPIOIEV
0x410 GPIOIM
0x414 GPIORIS
0x418 GPIOMIS
0x41C GPIOICR
0x420 GPIOAFSEL
0x500 GPIODR2R
0x504 GPIODR4R
0x508 GPIODR8R
0x50C GPIOODR
0x510 GPIOPUR
0x514 GPIOPDR
0x518 GPIOSLR
0x51C GPIODEN
R/W
R/W
R/W
R/W
R/W
R/W
RO
RO
W1C
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
0x0000.0000
-
0x0000.00FF
0x0000.0000
0x0000.0000
0x0000.0000
-
0x0000.0000
0x0000.0000
-
Description
GPIO Data
GPIO Direction
GPIO Interrupt Sense
GPIO Interrupt Both Edges
GPIO Interrupt Event
GPIO Interrupt Mask
GPIO Raw Interrupt Status
GPIO Masked Interrupt Status
GPIO Interrupt Clear
GPIO Alternate Function Select
GPIO 2-mA Drive Select
GPIO 4-mA Drive Select
GPIO 8-mA Drive Select
GPIO Open Drain Select
GPIO Pull-Up Select
GPIO Pull-Down Select
GPIO Slew Rate Control Select
GPIO Digital Enable
See
page
403
404
405
406
407
408
409
410
411
412
414
415
416
417
418
420
422
423
July 24, 2012
401
Texas Instruments-Production Data