English
Language : 

PIC16F753 Datasheet, PDF (196/238 Pages) Microchip Technology – 14/16-Pin, Flash-Based 8-Bit CMOS Microcontrollers
◁
PIC16F753/HV753
22.8 DC Characteristics: PIC16F753/HV753-I (Industrial)
PIC16F753/HV753-E (Extended)
DC CHARACTERISTICS
Param.
No.
Sym.
VIL
D030
D030A
D031
VIH
D040
D040A
D041
D042
IIL
D060
Characteristic
Input Low Voltage
I/O port:
with TTL buffer
with Schmitt Trigger buffer
Input High Voltage
I/O ports:
with TTL buffer
with Schmitt Trigger buffer
MCLR
Input Leakage Current(1,2)
I/O ports
D061
D063
D070*
IPUR
D080 VOL
RA3/MCLR(2,3)
PORTA Weak Pull-up
Current(4)
Output Low Voltage
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Min.
Typ† Max. Units
Conditions
Vss
—
0.8
V 4.5V  VDD  5.5V
Vss
— 0.15 VDD V 2.0V  VDD  4.5V
Vss
— 0.2 VDD V 2.0V  VDD  5.5V
—
2.0
—
VDD
V 4.5V  VDD 5.5V
0.25 VDD + 0.8 —
VDD
V 2.0V  VDD  4.5V
0.8 VDD
—
VDD
V 2.0V  VDD  5.5V
0.8 VDD
—
VDD
V
—
0.1
1
A VSS VPIN VDD,
Pin at high-impedance
—
0.7
5
A VSS VPIN VDD
—
0.1
5
A EC Configuration
50
250
400
A VDD = 5.0V, VPIN = VSS
I/O ports (excluding RA0, RA2)
—
—
RA0, RA2
—
—
D090 VOH
Output High Voltage
—
0.6
V IOL = 7.0 mA, VDD = 4.5V,
-40°C to +125°C
—
0.6
V IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
—
0.6
V IOL = 14 mA, VDD = 4.5V,
-40°C to +125°C
—
0.6
V IOL = 17 mA, VDD = 4.5V,
-40°C to +85°C
I/O ports(1) (excluding RA0, RA2)
VDD – 0.7
—
—
V IOH = -2.5 mA, VDD = 4.5V,
-40°C to +125°C
VDD – 0.7
—
—
V IOH = -3.0 mA, VDD = 4.5V,
-40°C to +85°C
RA0, RA2
VDD – 0.7
—
—
V IOH = -5.0 mA, VDD = 4.5V,
-40°C to +125°C
VDD – 0.7
—
—
V IOH = -6.0 mA, VDD = 4.5V,
-40°C to +85°C
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: Negative current is defined as current sourced by the pin.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
3: This specification applies to RA3/MCLR configured as RA3 with the internal weak pull-up disabled.
4: This specification applies to all weak pull-up pins, including the weak pull-up found on RA3/MCLR. When RA3/MCLR is
configured as MCLR Reset pin, the weak pull-up is always enabled.
D40001709A-page 196
Preliminary
 2013 Microchip Technology Inc.
 ▷