PIC16F753 Datasheet, PDF (169/238 Pages) Microchip Technology – 14/16-Pin, Flash-Based 8-Bit CMOS Microcontrollers

PIC16F753/HV753
TABLE 19-4: INITIALIZATION CONDITION FOR REGISTERS (CONTINUED)
Register
Address Power-on Reset
MCLR Reset
WDT Reset
Brown-out Reset⁽¹⁾
Wake-up from Sleep through
Interrupt
Wake-up from Sleep through
WDT Time-out
CM2CON1
9Ch
0000 ---0
0000 ---0
uuuu ---u
CM1CON0
9Dh
0000 0100
0000 0100
uuuu uuuu
CM1CON1
9Eh
0000 ---0
0000 ---0
uuuu ---u
CMOUT
9Fh
---- --00
---- --00
---- --uu
LATA
105h
--xx -xxx
--uu -uuu
--uu -uuu
IOCAN
108h
--00 0000
--00 0000
--uu uuuu
WPUA
10Ch
--00 0000
--00 0000
--uu uuuu
SLRCON0
PCON
10Dh
10Fh
---- -0-0
---- --qq
---- -0-0
---- --uu^{(1, 5)}
---- -u-u
---- --uu
TMR2
110h
0000 0000
0000 0000
uuuu uuuu
PR2
111h
1111 1111
1111 1111
uuuu uuuu
T2CON
112h
-000 0000
-000 0000
-uuu uuuu
HLTMR1
113h
0000 0000
0000 0000
uuuu uuuu
HLTPR1
114h
1111 1111
1111 1111
uuuu uuuu
HLT1CON0
115h
-000 0000
-000 0000
-uuu uuuu
HLT1CON1
116h
---0 0000
---0 0000
---u uuuu
ANSELA
185h
--11 -111
--11 -111
--uu -uuu
APFCON
188h
---0 -000
---0 -000
---u -uuu
OSCTUNE
189h
---0 0000
---u uuuu
---u uuuu
PMCON1
18Ch
---- -000
---- -000
---- -uuu
PMCON2
18Dh
---- ----
---- ----
---- ----
PMADRL
18Eh
0000 0000
0000 0000
uuuu uuuu
PMADRH
18Fh
---- --00
---- --00
---- --uu
PMDATL
190h
0000 0000
0000 0000
uuuu uuuu
PMDATH
191h
--00 0000
--00 0000
--uu uuuu
COG1PH
192h
---- xxxx
---- uuuu
---- uuuu
COG1BLK
193h
xxxx xxxx
uuuu uuuu
uuuu uuuu
COG1DB
194h
xxxx xxxx
uuuu uuuu
uuuu uuuu
COG1CON0
195h
0000 0000
0000 0000
uuuu uuuu
COG1CON1
196h
--00 0000
--00 0000
--uu uuuu
COG1ASD
197h
0000 0000
0000 0000
uuuu uuuu
Legend:
Note 1:
2:
3:
4:
5:
u = unchanged, x = unknown, – = unimplemented bit, reads as ‘0’, q = value depends on condition.
If VDD goes too low, Power-on Reset will be activated and registers will be affected differently.
One or more bits in INTCON and/or PIRx will be affected (to cause wake-up).
When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h).
See Table 19-5 for Reset value for specific condition.
If Reset was due to brown-out, then bit 0 = 0. All other Resets will cause bit 0 = u.
 2013 Microchip Technology Inc.
Preliminary
DS40001709A-page 169