IC-MN_16 Datasheet, PDF (16/62 Pages) IC-Haus GmbH – 25-BIT NONIUS ENCODER WITH 3-CH. SAMPLING 13-BIT Sin/D INTERPOLATION

iC-MN 25-BIT NONIUS ENCODER
WITH 3-CH. SAMPLING 13-BIT Sin/D INTERPOLATION
CONFIGURATION PARAMETERS
Rev F2, Page 16/62
Analog Parameters (valid for all channels)
CFGIBP: Bias Trimming (P. 28)
CFGTA:
Temperature Sensor Calib. (P. 28)
DCPOS: Input Current Polarity (P. 23)
ENF:
Noise Filter Enable (P. 28)
CVREF: VREF Source Selection (P. 23)
REFVOS: Offset Reference Source (P. 24)
RIN:
Input Resistance (P. 23)
TUIN:
Input Voltage Divider (P. 23)
UIN:
Signal Mode (P. 23)
Signal Conditioning
x = M, S, N (for master, segment, nonius channel)
ACOC_x: Signal Level Control: Current (P. 27)
ACOR_x: Signal Level Control: Range (P. 27)
ACOT_x: Signal Level Control: Op. Mode (P. 27)
GFC_x:
Gain Factor Cosine (P. 24)
GR_x:
Gain Range (P. 24)
GFS_x:
Gain Factor Sine (P. 24)
MPS_x:
Intermediate Voltage Sine (P. 25)
MPC_x:
Intermediate Voltage Cosine (P. 25)
OFC_x:
Offset Factor Cosine (P. 26)
ORC_x:
Offset Range Cosine (P. 25)
OFS_x:
Offset Factor Sine (P. 25)
ORS_x:
Offset Range Sine (P. 25)
PH_x:
S/C Phase Correction (P. 26)
Operating Modes
TRACMODE: Op. Mode Parameter (P. 21)
CALMODE: Op. Mode Parameter (P. 21)
BYP:
Bypass Switch (P. 21)
Sine-To-Digital Conversion
MODE_ST: S/D Conversion Mode (P. 30)
UBL_M:
Bit Length Master (P. 29)
UBL_N:
Used Bit Length Nonius (P. 29)
SBL_N:
Synch. Bit Length Nonius (P. 29)
UBL_S:
Used Bit Length Segment (P. 29)
SBL_S:
Synch. Bit Length Segment (P. 29)
FRQ_TH: Signal Frequency Monitoring (P. 32)
SPO_N: Offset Nonius Track (P. 35)
SPO_S:
Offset Segment Track (P. 35)
I/O Interface
TOS:
Timeout (P. 36)
DL_ST:
ST Data Length (P. 36)
M2S:
MT Data Output (P. 39)
ESSI:
Error Bit (P. 37)
GRAY_SCD: Data Format (P. 37)
RSSI:
Ring Operation (P. 37)
DIR:
Inversion Of Code Direction (P. 37)
I/O Interface With Extended Functions
NBISS:
Interface Protocol (P. 38)
TOS:
Timeout (S. 38)
DL_ST:
ST Data Length (P. 39)
M2S:
MT Data Output (P. 39)
DIR:
Inversion Of Code Direction (P. 39)
GRAY_SCD: Data Format (P. 39)
CID_SCD: CRC Start Value (P. 39)
NC_BISS: Communication Disable (S. 39)
ELC:
Sign-of-life Counter (P. 40)
Driver Settings
DSC:
Driver Short-Circuit Current (P. 41)
DTRI:
Driver Output Mode (P. 41)
DSR:
Driver Slew Rate (P. 41)
Command And Status Register
STATUS: Status Register (P. 43)
MN_CMD: Implemented Commands (P. 42)
AUTORES: Automatic Reset Function (S. 42)
Error And Warning Bit
CFGEW: Error And Warning Bit Config. (P. 45)
S2ERR:
Visibility For Warning Bit (P. 46)
S2WRN: Visibility For Error Bit (P. 46)
E2EPR:
Diagnosis Memory Enable (P. 44)
MT Interface
MODE_MT: MT Interface Operating Mode (P. 47)
DL_MT:
MT Data Length (P. 48)
SBL_MT: MT Synch. Bit Length (P. 48)
LNT_MT: Leading/Trailing Gear Box Assembly
(P. 48)
CHK_MT: Period Counter Verification (P. 48)
GRAY_MT: MT Interface Data Format (P. 48)
MT Interface with Extended Functions
MODE_MT: MT Interface Operating Mode (P. 47)
GET_MT: Direct BiSS Communication Enable for
MT Sensor via I/O Interface (P. 50)
NCRC_MT: MT Interface CRC Verification (P. 50)
SWC_MT: MT Interface CRC Polynomial (P. 50)
Preset Function
OFFS_ST: Position Offset for ST Data Output
(P. 51)
PRES_ST: Preset Value for ST Data Output (P. 51)
OFFS_MT: Position Offset for MT Data Output
(P. 51)
PRES_MT: Preset Value for MT Data Output (P. 51)
EEPROM Interface
CFG_E2P: Config. Of External Memory (P. 54)
CRC_E2P: EEPROM Data Check Sum (P. 54)
PROT_E2P: Register Access Control (P. 55)