33889 Datasheet, PDF (8/60 Pages) Freescale Semiconductor, Inc – System Basis Chip with Low Speed Fault Tolerant CAN Interface

ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics .
Characteristics noted under conditions - VSUP From 5.5 V to 18 V and TJ from -40°C to 125°C, unless otherwise noted. Typical
values noted reflect the approximate parameter means at T_A = 25°C under nominal conditions unless otherwise noted.
Description
Symbol
Min
Typ
Max
Unit
INPUT PIN (VSUP)
Nominal DC Voltage range
Extended DC Voltage range 1
Reduced functionality ⁽⁶⁾
Extended DC Voltage range 2 ⁽⁸⁾
Input Voltage during Load Dump
Load dump situation
V_SUP
5.5
-
18
V
V_SUP-EX1
4.5
-
5.5
V
V_SUP-EX2
18
-
27
V
V_SUPLD
-
-
40
V
Input Voltage during jump start
Jump start situation
V_SUPJS
-
Supply Current in Sleep Mode ⁽⁷⁾
V_DD1 & V2 off, V_SUP ≤ 12 V, oscillator running ⁽¹⁰⁾
I_SUP
-
(SLEEP1)
Supply Current in Sleep Mode ⁽⁷⁾
V_DD1 & V2 off, V_SUP ≤ 12 V, oscillator not running
I_SUP
-
(SLEEP2)
Supply current in sleep mode ⁽⁷⁾
V_DD1 & V2 off, V_SUP = 18 V, oscillator running ⁽¹⁰⁾
I_SUP
-
(SLEEP3)
Supply Current in Stand-by Mode ^(7),(9)
I_SUP(_STDBY)
-
Iout at V_DD1 = 40 mA, CAN recessive state or disabled
Supply Current in Normal Mode ⁽⁷⁾
I_SUP(NORM)
-
Iout at V_DD1 = 40 mA, CAN recessive state or disabled
Supply Current in Stop mode ^(7),(9)
I_SUP
-
I out V_DD1 < 2.0 mA, V_DD1 on ⁽¹¹⁾, V_SUP ≤ 12 V, oscillator
(STOP1)
running ⁽¹⁰⁾
Supply Current in Stop mode ^(7),(9)
I_SUP
-
Iout V_DD1 < 2.0 mA, V_DD1 on ⁽¹¹⁾ V_SUP ≤ 12V, oscillator
(STOP2)
not running ⁽¹⁰⁾
Supply Current in Stop mode ^(7),(9)
I_SUP
-
Iout V_DD1 < 2.0 mA, V_DD1 on ⁽¹¹⁾, V_SUP = 18 V, oscillator
(STOP3)
running ⁽¹⁰⁾
-
27
V
95
130
µA
55
90
µA
170
270
µA
42
45
mA
42.5
45
mA
120
150
µA
80
110
µA
200
285
µA
Notes
6. V_DD1 > 4.0 V, reset high, if R_STTH-2 selected and I_OUT V_DD1 reduced, logic pin high level reduced, device is functional.
7. Current measured at V_SUP pin.
8. Device is fully functional. All modes available and operating, Watchdog, HS1 turn ON turn OFF, CAN cell operating, L0 and L1 inputs
operating, SPI read write operation. Over temperature may occur.
9. Measured in worst case condition with 5.0 V at V2 pin (V2 pin tied to VDD1).
10. Oscillator running means “Forced Wake-Up” or “Cyclic Sense” or “Software Watchdog” timer activated. Software Watchdog is
available in stop mode only.
11. V_DD1 is ON with 2.0 mA typical output current capability.
33889
8
Analog Integrated Circuit Device Data
Freescale Semiconductor