DS90UH926Q-Q1 Datasheet, PDF (9/58 Pages) Texas Instruments – 720p 24-Bit Color FPD-Link III Deserializer With HDCP

www.ti.com
DS90UH926Q-Q1
SNLS337K – OCTOBER 2010 – REVISED JANUARY 2015
6.6 AC Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.^{(1) (2) (3)}
PARAMETER
TEST CONDITIONS
PIN/FREQ.
MIN
GPIO BIT RATE
Forward Channel Bit Rate
B_R
Back Channel Bit Rate
See ^{(4) (5)}
f = 5 – 85MHz,
GPIO[3:0]
> 50
CML MONITOR DRIVER OUTPUT AC SPECIFICATIONS
E_W
Differential Output Eye Opening
Width ⁽⁶⁾
E_H
Differential Output Eye Height
BIST MODE
R_L = 100Ω,
Jitter Freq >f / 40
Figure 2 ^{(4) (5)}
CMLOUTP,
0.3
CMLOUTN,
f = 85MHz
200
t_PASS
BIST PASS Valid Time
BISTEN = H
Figure 8 ^{(4) (5)}
PASS
SSCG MODE
f_DEV
f_MOD
Spread Spectrum Clocking
Deviation Frequency
Spread Spectrum Clocking
Modulation Frequency
SeeFigure 14, Table 1 and
Table 2 ^{(4) (5)}
f = 85MHz,
SSCG = ON
±0.5%
8
TYP
0.25*f
>75
0.4
300
800
MAX UNIT
Mbps
kbps
UI
mV
ns
±2.5%
100 kHz
(1) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and
are not ensured.
(2) Typical values represent most likely parametric norms at V_DD = 3.3 V, T_A = 25°C, and at the Recommended Operation Conditions at the
time of product characterization and are not ensured.
(3) Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground
except VOD and ΔVOD, which are differential voltages.
(4) Specification is ensured by characterization and is not tested in production.
(5) Specification is ensured by design and is not tested in production.
(6) UI – Unit Interval is equivalent to one serialized data bit width (1UI = 1 / 35*PCLK). The UI scales with PCLK frequency.
6.7 DC and AC Serial Control Bus Characteristics
Over 3.3-V supply and temperature ranges unless otherwise specified.^{(1) (2) (3)}
PARAMETER
TEST CONDITIONS
MIN TYP
MAX UNIT
V_IH
V_IL
V_HY
V_OL
I_in
t_R
t_F
t_SU;DAT
t_HD;DAT
t_SP
C_in
Input High Level
Input Low Level Voltage
Input Hysteresis
SDA RiseTime – READ
SDA Fall Time – READ
Set Up Time — READ
Hold Up Time — READ
Input Filter
Input Capacitance
SDA and SCL
SDA and SCL
SDA, IOL = 1.25mA
SDA or SCL, Vin = V_DD33 or GND
SDA, RPU = 10kΩ, Cb ≤ 400pF, Figure 9
SeeFigure 9
SeeFigure 9
SDA or SCL
0.7*V_DD33
GND
>50
0
-10
430
20
560
615
50
<5
V_DD33 V
0.3*V_DD33 V
mV
0.36 V
+10 µA
ns
ns
ns
ns
ns
pF
(1) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and
are not ensured.
(2) Typical values represent most likely parametric norms at V_DD = 3.3 V, T_A = 25°C, and at the Recommended Operation Conditions at the
time of product characterization and are not ensured.
(3) Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground
except VOD and ΔVOD, which are differential voltages.
Copyright © 2010–2015, Texas Instruments Incorporated
Product Folder Links: DS90UH926Q-Q1
Submit Documentation Feedback
9